Search results for query: *

Finally mating my trans up to engine on the cradle. Everything is going smoothly and the four smaller bolts are going in with my fingers. Lower passenger bolt starts just fine, but needs the wrench to get it most of the way in. Driver side bolt starts fine for two or three turns. Then put a...

I have a 69 GTX that a purchased as an incomplete project. The 440 has been professionally rebuilt by previous owner and remains pretty stock, no performance mods from what I was told. The project came with many parts to complete the car to include a Mancini Pro Billet distributor and an MSD 6AL...

Built the K member dolly along the lines of others I have seen on here. But built my own front end dolly so I could roll the GTX off the lift while k member was out. Waiting on Amazon to deliver another wheel, and then finish welding her up with a coat of paint. What do you guys think? See any...

I just purchased this 69 Bee. It is a numbers matching true Super Bee coupe, 4 speed, 383. Factory quarter scoops and N96 options. Texas car it's whole life. Parked for many years. Im the third owner. The previous owner bought the car a year ago from original owners and started doing a low...

I am picking up a 1969 Super Bee project this week and have a couple questions on my fender tag. This is what I figured out so far, but there are a couple I am not sure of….Thanks in advance! E63…..383 4 Barrel HP D21…..4 Speed manual HD WM31….Dodge Super Bee 2-door coupe H9G……383 CID V8...

Did the carpet installation this weekend for my 69 GTX restoration. Pretty happy with results. A little more steam and should be wrapped up today.

I've read all the threads and debates on wether the air grabber vent grills are red or black from factory. Alot of assumptions and real life knowledge for sure. I think the debate ended with early 69 air grabber could be black, but sometimes red. And then which factory was it assembled? Too many...

Restoring my 1969 GTX and I am needing the small cable clamp that holds the cable down on the control unit. See pic.

Restoring my 69 GTX and I'm missing the small clamp that hold the fresh air cable to the dash control unit. Can't find any supplier who carrys one. Anyone have a source for one?

Im restoring my 69 GTX and latest effort is the headrests. Im restoring my original headrests and needed to replace the chrome trim that goes around the vinyl channel. The old must be ground out as it is basically welded into the vinyl. After grinding it all out, I was not happy with the chrome...

Putting my console togeather for my 69 GTX. Carpet for sides is straight forward. But how does the rear console carpet get installed?? Any alignment tips? What is the purpose of the vinyl on the ends?

I need to swap out my 2 speed motor for a 3 speed unit in order to install my N96 air grabber setup. Purchased this 68 3 speed motor and decided to restore it myself today. First time working on one of these and nothing very difficult so far. Will try to find a firewall rubber seal for it...

I’m getting the parts together to install my N96 option. I have the three speed switch for the wiper. Now I’m needing the 3 speed motor and the small bracket to connect to arms. Not picky on date coded. Thanks, Jim C

I am restoring my 1969 GTX and have a couple questions on the Console Performance Indicator. Obviously the two wires are ground and power for the light bulb inside the Indicator. But is there a specific connection point that they tie into? Don't see this option on my wiring diagram, and cant...

I need a set for my 69 GTX restoration. Prefer factory clips, but at this point I will even settle for repop. Looks like alot of people are looking for these without much luck.

Im installing a headliner for the first time in my 69 GTX. Never done one before. I have read alot of threads on how to do it and think I am looking pretty good so far. Just wrapped up glueing and stretching it into place. But obviously I have some wrinkle spots that seem to be a potential...

I wish I had taken some before and after pics, but very happy with how my window trim in coming out. I hit the chrome and stainless with my buffing wheel and took my time on them. They were fairly rough to start, but fortunately very little to no pitting. Also sandblasted some of the inner...

Looking for a tail panel for my 69 GTX restoration. Must be in excellent condition, or an aftermarket repot. Let me know what you have.

I’m needing the two corner pieces of dash trim for my 1969 GTX. Not needing the wood trim pieces, just the “J” shaped stainless steel pieces. Let me know what you have.