Follow along with the video below to see how to install our site as a web app on your home screen.
Note: This feature may not be available in some browsers.
When you click on links to various merchants on this site and make a purchase, this can result in this site earning a commission. Affiliate programs and affiliations include, but are not limited to, the eBay Partner Network.
I saw this thread looking for information.
the Packard 59 are also now called Delphi, Aptiv, or Packard terminal ends.
The 59 is a wider version of the 56 series. It goes in the mopar and the gm headlight housing plugs.
mopar and gm also share the Packard 56 for about every other terminal...
slider that connects to the carburetor for the 4 barrel (not the 2 barrel)
Throttle bracket for 4 barrel
Carburetor linkage for slider and throttle cable
Holley 20-7 of anyone has it lying around for the linkage hook up.
its really interesting to watch this surgery.....I don't think ive ever seen such an undertaking. I know i will now be removing my cowl after seeing the mess that was inside....maybe even setting up a removable plate to get to these areas once in a while....It is horrible to see cars in even...
I cannot get my car to charge....heres what ive done so far.
replaced the regulator 2 times. has a 76 regulator on it. I get 12 volts running at the field wires. checked to see if the plug was bad.
replaced the alternator with 2 used alternators. Both checked out on 3 parts stores...
on most cars i can see using other metal. the darts roof rail is a complex bend that starts shallow curve in the front and ends larger in the back...then has 2 90 degree bends. i wonder what other car has this bend. I would love to have the skills and equipment to make this stuff from scratch...
have successfully filled in around 200 small pin holes on the roof rail of my 69 dart. I have only done the drivers side so far. The problem im having is in the grinding of the fill welds. They are so close together that when i grind them down they are paper thin and stacking on top of each...
ive replaced the pump with the correct pump and installed the seal and washer right next to the snap ring. this was another new seal and should have had no room to travel and leak. it is leaking where the seal meets the housing and is leaking worse than usual this time. new lines and pump.
can you tell me how to install it correctly. i have a 1 1/8 socket with the end cut off so it will fit over the shaft. i put an extra washer on the seal and then hammer it until it seats at the bottom. seal looks good in there. with the washer it is about 1/8 inch from the snap ring...soon as i...
so im running the 68 coronet pump.....which may have too much pressure...... my pump spring may be stuck closed? or the veins may be sticking. maybe a new pump is in order...this is the 5th new seal in there. my original box blew a seal...i replaced the box with this one from a 70 cuda....it...
it is a saginaw pump. it blew the seals with no stress on the steering.. could that extra 400 psi from the 68 coronet pump blow the steering box for an a body
are a and b body power steering pumps interchangeable. i have a 68 coronet pump on my 69 dart and i think that its blowing the seals out of my steering box. is this possible
i heard 66 through 69 were the same seat frames in the A and B bodies. I then heard 66 and 67 only sometimes had the holes in them, but the 68 and 69 always did. I never got confirmation that the 66 seats were the same as the 69. I know for a fact 65 was different. Does anyone know how to...
the castle nuts are the large rings that hold the guts of the steering box in place. They look like the top of an old castle. I did buy that cd but its not here yet. My rebuild kit came with extra o rings and not enough o rings. THe extras i dont need , but there seems to be one missing. I dont...