Search results for query: *

Had to fill out a sheet of all options on the car. The color it was painted. Type motor. Gave the Vin tag number also. Now this was just to fill that blank space under hood and will never sell it as the original tag. It doses state on tag Reproduced.

Check all connections under dash. Just had my head light switch connection go bad. Nothing worked on the car. Replaced the start run switch and nothing. Good battery. So, under dash wiggled wire connectors and low and behold the head light switch connector made everything come on and car run...

MMC made mine and had all options I put on the car plus color of vehicle. The two screw holes where empty on the inner fender so wanted to fill that spot. LOL. Build sheets came from the factory and many time are destroyed by critters or are lost over the years. Good luck. Build it like you want it.

I like it. Good job.

Nothing looks burned there. Used contact cleaner on all connections at the bulkhead connector. Reading voltage on the blue wire at the plug end of wire harness. Contact block looks good also. Scratching my head trying to figure it out. I guess back to the drawing board. Will run an AMP draw on...

So yesterday opened the driver's door and console light and dome light went off and thought I hear a pop. Now no power to the car inside. No power at starter switch. Everything under hood shows power. Even checked the blue fusible link on bulkhead connector shows power their but have not checked...

Manifolds look good. Coated mine on outside with coating from east wood. Still looking shiny even after driving for a while.

Can't buy me LOVE.

Do - Don't that is the question. LOL Will see when they are here. Found a set on E bay. Thanks for the response. Blue. :thumbsup:

Were to get gravel or mud flaps for 69 Plymouth roadrunner. Would like something like chrome or stainless steel. Or maybe I can get something in a black that I could paint. Starting to see chips on wheel opening to the back on the rear quarters. Don't like it and trying to find an answer. Thanks...

Ok the draw was from the coil. New EDB coil on and is running fine. Think I do need to locate it on the passenger inner fender going to work on that the next couple of days. It is horizontal attached to the intake manifold near the distributor. Think the heat from the engine may be taking an...

Ok not enough info sorry. After market electronic ignition. Bought from summit. Cleaned the bulkhead connections. Checked my battery terminal's. It fires up and shakes violently. It just might be the coil will be off to get one tomorrow. It is not that old, but we know electronic parts now...

I can find what size ballast resistor I need. Any help would be greatly appreciated. Yes looked into my manual but no luck on size of resistor.

Thought about that but it is not that old. They do go bad thanks will add that to my list to check.

While driving my Roadrunner yesterday. Was running fine the 383 was humming along then it started braking up and shut down. Pump the pedal and it fires but dies. Tried several times to get it to run. Same over and over. It fired but just died. Have fuel in the site glass on the new Holley...

The new lifters just are not as good as the old ones we use to get. I have other people saying the same thing. I have dome head piston's and have to watch the length of my spark plugs. Ask me how I know. Could hear a tick sound. found the piston was striking the ground strap. Not good. Good luck...

Yes, they are scrambling to cover their own jobs. A total failed administration for sure. Save a minnow and lose homes that is the question. What were they thinking. What a sad day for those people. These issues have been addressed but nothing was done. Nero fiddled while Rome burned need, I say...

Welcome. Hope you enjoy the site. Lot of good people here and willing to help and listen. :thumbsup:

Very nice car. Have fun. Looks really clean inside and out. :thumbsup:

So sad. Think if the water was available and not drained out of the reservoir's then more could have been saved. Due to people not wanting to do pre burns or brush removal this is what happens. Yes, without the brush and root systems then you have mud slides. It is bad that insurance companies...