Search results for query: *

Thanks for taking the time to document your experience with this install process. I’m looking forward to doing this swap on my 72’ RR and any info that can be collected in advance is helpful.

I have an essentially brand new set of Eagle Alloys 15x7 rims with BFGoodrich Radial T/A front 245/60R15 rear 275/60R15 They were bolted on to my Roadrunner to move it around the shop I’m asking $500 Pick up anytime in Burlington, MA Chrysler Nationals , Carlsile PA They could also be...

What is the part number on that shroud?

You should be able to find the offset you need here….. https://www.sikky.com/product-category/shifter-relocation-kits/page/2/

Regardless of what type of finish you put on the floor I would not suggest laying it down without prepping the concrete. Keeping it clean until you coat it is the right thing to do but it doesn’t mean there will be no prep. Either an Acid etch or machine abrasion is going to be needed for most...

The use of a bubble level isn’t the best way to prove the angle without a reference, like the fender rail or something to that effect.

I agree with everyone asking what you are using it for. i just put an addition on my shop and had to make the same decision. My current shop has the cheep Rustoleum epoxy system from Lowes. It held up reasonably well for 20 years but its not something I would choose again. I gave the concrete...

I ended up going with a similar setup to yours. QA1 K, uppers, lowers, strut rods and sway bar. Also used Borgeson box, Bergman tie rods, pitman/idler and hemi torsion bars. I did the Baer T4 brakes as well. I ended up buying a USCT stiffening kit which was a late decision in the project. I’m...

Yep, the tag is mostly broken off the rivet. There is a chance that I have the tag somewhere. This motor has been under a bench in my shop since the early 80s so hopefully it’s around. I’ll keep an eye out for it.

I have a complete 71’ 383 warranty motor. Turquoise block date coded 11-17-70 The VIN pad is machined but doesn’t have a vin stamped into it. This motor was from a 67’ Newport The motor was replaced under dealer warranty in 71’ It is a complete motor from oil pan to intake manifold. The motor...

Glad I brought your excitement level back up a notch. On the 4-post you are going to have to get the front lifted off the suspension regardless. You will probably need a cross beam to hang the engine and the rest won’t be a huge deal. I pre-assembled everything including the brakes and...

My original post only listed the front tire size. Rear tires are 275.

I just did this setup on my 69’ Coronet R/T

I just painted my 69 Coronet R/T black with a red tail stripe so that covers that but I also agree that most cars look good in black.

I have an essentially brand new set of Eagle Alloys 15x7 rims with BFGoodrich Radial T/A 245/60R15 tires mounted on them. They were bolted on to my roadrunner to move it around the shop but never actually hit the road. I’m asking $500 Pick up anytime in Burlington, MA They could also be...

Why is it not so common in the Mopar world to run high/low breather catch cans so both systems can function as designed but without sending the crap back into the engine or all over the side of it? I use sealed breather catch cans/separators (can hold vacuum or pressure) on the PVC side of some...

Ah, I see what you did there. LOL They actually fit really well and even the little bit of grinding is disclosed in the instructions. Most of the time stuff like that is a surprise for you to figure out on your own. Baer makes a nice product with what I would consider to be a near OEM level...

In regards to the brake lines the instructions from Baer say that if you have front mounted calipers that you need to swap you spindles to the opposite side of the suspension so that you will be installing the kit in the rear mounted position. I had to grind the top bolt hole for the bracket...

Thank you. Did you cut the frame side down a bit? They don’t come up on ARPs site when I search for AR2.500-1b I don’t see them on summit but found them on another site as a special order item. https://ljrc1.com/item/4579633-12-stud-2500-long-broached Does that look right? On summit I can...

I purchased a partially finished 69’ coronet R/T over the winter that came with a fresh engine build and included a cast iron six pack intake and a set of 340 Six Pack carbs as well as a bunch of linkage in a box. I have no idea if any of the linkage that was in the box is actually correct for...