Follow along with the video below to see how to install our site as a web app on your home screen.
Note: This feature may not be available in some browsers.
When you click on links to various merchants on this site and make a purchase, this can result in this site earning a commission. Affiliate programs and affiliations include, but are not limited to, the eBay Partner Network.
Thanks!!! As for my time , fortunately I'm retired but still do a little consulting work . If I counted my time at $1.00/hr I've probably got $1,000,000,000.00 in this car. LOL!!!! I'm just a little concerned as to getting everything correct, putting it back in and finding out I left that one...
That's what I was kind of afraid of after reading that those seals can leak. I've never torn into an automatic transmission before but after watching some of the videos it doesn't look that bad to do a "Soft" rebuild. What's everyone's thoughts? I've done a couple of LS swaps, rebuilt a couple...
Good point. What kind of pressures should I see? I can look it up but which opening is which as far as supply/return or in/out or does for pressure does it matter?
So, I apologize for being a Dumba....s up front. I was wrong on the spline count. I was looking at the outer count not the input shaft. See attached photo of the old Torque Convertor. Zoom in and it looks like 19! I know this can't be. The other photo is before I installed the "New" engine. If...
And the plot thickens!!!! If my memory serves me correctly I only remember the filter having one hole. But if I actually needed a two hole filter, and used the one hole, wouldn't the problem shown up sooner? I'm basing my years and model of cars the engine/trans came from on information I got...
I'll check that. Although when I do put it in Drive or First I can still feel, albeit slight, a "Clunk" like its going in gear. The one thing that still blows my mind is the last time I drove it it seemed fine. Park it in a heated garage, come back 4-5 weeks later start the car and immediately...
Yes it's an unmodified transmission. The original engine was a 1963 413. The replacement engine is a 1976 440 block and internals as I understand. The seller of the new engine is a big Mopar guy and because the new engine is internally balanced as opposed to the original it required a different...
I don't recall the number of holes on the original or replacement filter. The replacement came from Fatco Transmission along with O-rings for the cables and gaskets for the pan and the reverse cable cover. Would it take a few miles and drive cycles for the problem to show up with the wrong...
I've not done any diagnostics on it yet. I agree with you that a weak pump might be the issue. But, to answer your question yes it did seem to work fine after my initial fluid/filter change. Although in retrospect the car didn't/doesn't seem to have the punch to it when I would floor it. And I...
Hello All,
So I got my 1964 Plymouth Fury up and running that had not been run since at least 1976. Put a rebuilt engine in it, new Torque Converter and changed the trans filter and fluid. The old fluid looked good and no sparkles in the pan. I've driven the car about 50 miles since then over...
Wow!!! Again, I've read they do excellent work but years for seat covers/door panels. Although one car upholstery shop quoted me eight to twelve hours labor to make/install new covers. That's a 50% spread!!!! I used to do Piping estimation. I'd never gotten a job with that kind of estimating...
Well I just opened the roll of vinyl I received Friday from SMS. They sent the regular vinyl and the invoice says the ribbed vinyl will ship later. I asked specifically if both were in stock and they said yes. Now I'm concerned. I'll be calling Monday
Wow!!!!! If your still waiting six years later that "Around six month turn a round " I was told must be way out in left field. Thanks for the input. This really backs my decision to go with someone locally. I'm in a bit of an interesting position. While I like my car it's not a 100% all original...
This subject couldn't've have come at a better time for me. I just received the vinyl for my 64 Fury from SMS this week. I had received an E-mail from them in December offering a 10% discount thru December. I had received samples from them close to a year ago. They quoted me roughly $700.00...
Merry Christmas Everyone!!!! In a shameless plug for my new YouTube channel: ebby@ebbys123garage, check out my 1964 Plymouth Fury Wagon. I love this thing, even if my Wife doesn't LOL!!
So, check out my videos and give me some feed back. It's new so it doesn't pop up easily. Just type in...