Search results for query: *

OE replacement oil sending units are made in China, and have a wide range of tolerances. Plus the OE guage has a thermal movement mechanism, making it read slower. Just my $0.02... :thumbsup:

Nice interesting chart but.. The crucial factor is not voltage but available current battery reserve.. A battery can test @ higher voltage but when the starter current draw is applied the voltage can/will decrease big-time... Just my $0.02... :thumbsup:

I have been with Hagerty for >20 years for my RoadRunner, been very smooth to work with. Unlike my other cars insured by AAA just went up 30%, but had no tickets, no claims, no accidents.. Just my $0.02.... :thumbsup:

Problem with the Cranes was the rocker arm tips, not being hardened properly and would wear through... Note that this was a short time before they went bankrupt... Apparently their quality control process went down the tubes... But going back a few years, their quality control was very...

Another alternative is use the button head bolts, lower height profile... Just my $0.02...

My experience with mopar big block Crane rockers was a nightmare.. :rolleyes: They were not hardened properly and the tips wore through.. Contacted Crane @ SEMA and brought some of the worn rockers as an example. Talked with one of their engineers and he blew out screaming in the SEMA booth...

I was getting gas @ company owned Texaco station filling up..... I needed about 15 gallons but the pump stopped @ about 8 gallons couldn't restart it.. Went inside talked to the attendant, he paused and restarted the pump but @ a higher price...:lowdown: Apparently their the pricing on the...

I had mine powder coated gloss black... I had some other heater box parts done @ the same time for a batch price. And now 20 years later it still shine well.. Just my $0.02...

Basically (4) speakers, (2) in the front for the stereo 8-track, (1) in the front for the AM radio, (1) in the rear for the AM radio.... Just my $0.02... ;)

The contacts within the high/low dimmer switch often oxidize... Due to lack of use.. Suggest that U push the switch In/Out multiple times to burnish the contacts... If still issues, replace the switch... Just my $0.02...

Double-check the bulkhead connectors, these often get oxidized making poor electrical connections. Pull apart, polish the contacts and re-install using dielectric grease.. Just my $0.02...

Key point is this clearance will decrease as the clutch wears.. 1/8" to 1/4" should be fine. If there is not enough clearance for the throw-out bearing, it will wear down the pressure plate fingers possibly causing the clutch to slip. If all of the clutch link system is in good condition then...

Double check the free play down below between the throw-out bearing and pressure plate.. The throwout-bearing should be about 0.25" away from the pressure plate.... Just my $0.02...

The Octane LED headlights draw considerably more watts than the Holley retro brights. The Octanes require 40W for low/high beam and the Holleys require 30W a decrease of 25%. So here again double check the headlight wiring, grounds as to minimize any losses for the best results... Just my...

Holley has been shipping their LED retrobrights for 6 months, but inventory levels have been spotty due to unreliable delivery schedules. I installed (4) a few months back in my 70 RR. Very satisfied, they are bright and I made my own wiring harness, so I have (4) low or (4) high beams...

Very kool... However no way that can output 200W....:lol: Maybe 50W(25Wx2) at best.... Just my $0.02... :thumbsup:

In my 70 RR, I have a built 383, shroud, clutch fan, 22" radiator modified withe a 3 core Modine section. In SoCal it does get hot, the RR runs about 185 and up to 200 if in traffic. Biggest negative for electric fans is the juice they draw, up to 30 amps on start up and 15-20 amps running, so...

Can't comment much about the present day repro parts but... For my 70RR that was an original air grabber car, I have low vacuum(< 8") and my air grabber door opens/closes fully...

Good luck with SF.... 1 of their policy holders crashed into the back of me @50MPH.. He was cited for reckless driving but when negotiating with SF, it took 12 months to settle the property damage and 18 months to settle the physical injury damage. Every step with SF was a fight, left me no...

Keep in mind... Hagerty is just a broker, the actual insurance is outsourced... But I do agree, my experience with Hagerty has been positive.. Just my $0.02..