Search results for query: *

My buddy went along to Cecil County Dragway in MD and snapped some photos. He's the same one that took the photo of the R/T along the Susquehanna at dawn. The car ran a 12.8 @ 113 on street tires with a 4 speed and 3.54 gears. My first time down the track with it!

Anyone have a drivers door window sweep for a '69 Coronet? Mine is missing and I really don't want to buy a whole new set. I'm hoping someone has one laying around they would be willing to sell.

Can anyone tell me where to get a C-3951 shifter alignment tool? There is a slot for a neutral alignment pin but it doesn't go all the way through. The reverse tang is in the way. The manual refers to the C-3951. Is there any other way to get all the tangs lined up?

Can anyone tell me on the shoulder harness for a '69 RT, does the elastic strap snap on the harness or on an attached snap behind the harness mounted through the head liner? thanks!

Anybody have a recommendation on where to get a new tapered tube for a 69 b body?

I am installing a stand alone MSD Distributor that only requires the two wires from the distributor to the coil. I also need a 12 volt wire to the positive side of the coil. If I no longer need the ballast resistor, which wire do I use for the coil? There is a brown blue double wire on the left...

Need some advice- on my '69 RT, the pax side wiper arm bushing is worn out. The wiper arm will only move intermittently. Does anyone sell a replacement bushing? Can they be replaced or does the entire wiper pivot on the firewall need to be replaced? Its interesting how it can be such a...

Looking for advice/opinions, just finished assembling a 440 stroker motor stroked to 500". It should be around 500 HP. I don't anticipate spinning the motor more than 6000 rpm at the track. I have a 6 qt Milodon oil pan, melling high volume pump and a 3/8" pickup. I am also running a scraper...

Does anyone know, is there a difference between backing plates for 11 x 2 and 11 x 2 1/2 backing plates? I have a '69 Coronet RT I'm working on with a Dana 60 and just installed 11" backing plates but the 11 x 2 1/2 shoes don't seem to fit quite right. The only markings on the backing plate are...

Hopefully this is an easy question- I have an early build (Oct '68) 1969 Coronet RT that is a power assist drum brake car. It has the Dana rear end but 10" drums on the back and 11" drums up front. Is this a factory arrangement or were the brakes changed on the car at some point? Thanks!

Hello all, i have a 69 RR, auto on the floor and it won't start in park only neutral. I tested and replaced the switch. I did test on the car and it would start in park before I put in the tranny. My question is- what linkage do I adjust for this problem? I would like to fiddle with the...

Any suggestions for buying replacement 11" front drums for a '69 Coronet? I see adds on EBay but they look like Chinese made junk....measurements in metric....any suggestions appreciated.

For the convertible guys out there- I have a 69 RR convertible. Is there a trick to installing the snaps on the top cover? What's the best way to locate the snaps? Also, there is an additional piece that attaches to the plastic along the top of the back seat. It is black and has a piece of...

I have a 340 4 speed Cuda with a Predetonation issue. If I set the timing at 5 degrees BTDC, whenever I hit the throttle hard it brings like crazy. At 10 degrees ATDC it's not so bad. The engine is a low compression '73 motor that's got a cam slightly more aggressive than stock. Is there...

Has anyone rebuilt a B Body Wiper Motor? Do they make rebuild kits for 3speed wiper motors? My wiper motor is 2889 981 42166 3547 does anyone now what month and year it was made? Are there any date code source guides for B Body wiper motors?

Can anyone tell me on the 3speed wiper switch, there are two posts that are separate from the terminal. The bottom post is the brown wire loop to the washer switch, what is the vertical post for? What wire connects to it? thanks!

Can a 69 383 HP Flywheel be swapped to a 69 internally balanced 440?

Is anyone reproducing the 69 b body wiper harness that connects to the switch? Google is not turning up anything but 2speed harnesses.

Need some more advice- I have a69 RR convertible. On the front edge of the driver glass is a thin plastic channel. Does anyone reproduce it? thanks!

Ok guys, I'm building a 440 stroker (500), with Edelbrock performer RPM heads and intake with a comp extreme energy cam (525 lift, 110 degrees, 231/237). This is going in a 69 Coronet 4spd with 3.54 gear. I was thinking of a demon 850 but open to suggestions.... also, any issues with using a...