Picked up 2 sets of real nice 68 charger doors...a pair of absolutely clean 70 sport satellite fenders...and a nos 4-door quarter, possibly for 70 Plymouth. Don't really need any of it...just add it to the hord.
What Part/s Did You Buy Today for Your Hobby or Project ???
- Thread starter PROSTOCKTOM
- Start date
- Local time
- 5:15 AM
- Joined
- Jan 16, 2011
- Messages
- 77,331
- Reaction score
- 122,806
- Location
- NorCal Sierras
Yeah 'sort of' not a reservation to say, but a village
not sure they go by that there, I will check though
my dad says; "they don't have an actual reservation here"
I had no clue, he's been up here, since 1980
For sure, I need to drive my RR more too
seems every time I go to drive it a needle & seat are stuck or fuel overflowing etc.
it's getting old
nothing I can't handle, just getting really tired of it all
I've been busy of late with dad's (88) health & DR's appt.s etc.
neglecting my stuff, hard to get motivated "sort of"
after I do what ever I may decide,
I may start buying race fuel again, in a drum etc. & doing a mix
I may go to the airport down in Columbia 30+miles, down the hill
& get some avgas too
I know people (neighbor Shea, 22), otherwise that can get me a couple 5 gal jugs of it
every so often & do a blend at a min.
that work there (neighbor's son) 'sort of',
well he teaches flying lessons (for CalFire applicants) privately there
I'm sure he has a fuel-pass (card) they are really strict there...
Thanks
I have a NOS left tail light bezel for my Satellite. Have had it for 30+years, been looking for a right hand bezel. Have seen one with a lens but the price was $535 to much for me! Today I was on ebay, I seldom check it. I was on there because they turned on email notification for parts and I was turning them off. I get to my 1966 tail bezel search and right on top is an NOS right hand bezel at a reasonable price. Score! By the way they didn't notify me.
ckessel
Well-Known Member
The correct, for cast crank, flex plate came in yesterday from Mancini. I sent it off to Fresno for the machinist to have when its balance time.
33 IMP
Well-Known Member
- Local time
- 5:15 AM
- Joined
- Dec 21, 2017
- Messages
- 14,060
- Reaction score
- 23,779
- Location
- taxifornia,soon 2b Arizona.
After struggling with trying to make some braided line and fittings join up (used to do this fairly easily, apparently lost the talent) bought a koul tool for assembly ease...... and a few fittings, some braided line, and a bracket for a fuel regulator mount to a carb, that I could have made in ten minutes when I was working. Oh well.
Since mounting the regulator on the firewall is nhra illegal, and I don't have inner fenderwells, had to come up with something else.
Since mounting the regulator on the firewall is nhra illegal, and I don't have inner fenderwells, had to come up with something else.
33 IMP
Well-Known Member
- Local time
- 5:15 AM
- Joined
- Dec 21, 2017
- Messages
- 14,060
- Reaction score
- 23,779
- Location
- taxifornia,soon 2b Arizona.
I never buy diesel in california if I can help it. It may be crap,... but it's EXPENSIVE crap. I buy as much diesel as I can in Arizona, before my Cali trips.
33 IMP
Well-Known Member
- Local time
- 5:15 AM
- Joined
- Dec 21, 2017
- Messages
- 14,060
- Reaction score
- 23,779
- Location
- taxifornia,soon 2b Arizona.
I have an Indian casino nearby here in AZ, with a gas station and smoke shop, but it's across the river in Nevada, and gas/diesel prices are around 75 cents/gal higher than on my side. It has alky in it too.
But the Nevada gas is still at least a buck cheaper than the California side of the river!
But the Nevada gas is still at least a buck cheaper than the California side of the river!
Last edited:
- Local time
- 8:15 AM
- Joined
- Dec 10, 2013
- Messages
- 1,015
- Reaction score
- 1,526
- Location
- West Central Indiana
Bought a bunch of Timken bearings for the Dana 60 project from Rock Auto and used this discount code below for 5% off.
311615217194457695 Expires on September 12, 2025, 12:00 Midnight CT
Tom
311615217194457695 Expires on September 12, 2025, 12:00 Midnight CT
Tom
Vaanth
Well-Known Member
Belvedere408
Well-Known Member
- Local time
- 5:15 AM
- Joined
- Jan 25, 2023
- Messages
- 615
- Reaction score
- 1,259
- Location
- Springfield Oregon
Got the wheel installed today.
Similar threads
