• When you click on links to various merchants on this site and make a purchase, this can result in this site earning a commission. Affiliate programs and affiliations include, but are not limited to, the eBay Partner Network.

Search results for query: *

  1. 1967coronet

    Connie Francis Won't Be "Where The Boys Are"

    RIP Connie
  2. 1967coronet

    1967 Coronet 440 header questions

    Big Block Mopar Tri-Y Under Chassis Headers Schumacher Tri Ys . I bought a used set years ago they fit with no mods, easy install , good starter and plug access. They were closed at one time but are now back open under new owners. Cost is lower than tti, I had seen a track test on them ...
  3. 1967coronet

    Scarebird (uscartool.com) B Body Part Numbers

    I can not say they will, road wheels and plain old steel are built different on the back side. If i recall there is one less step down on the road wheels. The Lincoln 10.75 im running only clear by a 1/4 inch. I emailed with the scarebird guys when I was adding mine they were a good bunch to...
  4. 1967coronet

    Scarebird (uscartool.com) B Body Part Numbers

    I used the scarebird swap on my 67 same parts as qkcuda, I went with the 10.75 lincoln rotors , the do fit a 14" steel wheel. I have had no problems with the set up. Stops great. Pretty easy install.
  5. 1967coronet

    SKIN CANCER IS NASTY STUFF

    Moes I hope the recovery time goes fast for your and you out and about soon.
  6. 1967coronet

    Finding top dead center with a 9/16 wrench

    If you do pull that crank pulley mark it and the balancer for re assembly.
  7. 1967coronet

    MrMoparts? are you serious?

    I had to go back and read that 1st post again. Well ..... ok.
  8. 1967coronet

    Happy Birthday lewtot184

  9. 1967coronet

    Happy birthday Unkle Krusty

  10. 1967coronet

    1967 Coronet 440 intake

    Drop bases are fine but as mentioned you have to watch for fuel inlet and trans linkage room. My 67 coronet has the 2191 preformer , the 1/4" thick heat resistant fiber base gasket. Thermoquad and a 3" air cleaner regular base. I still have a little over 1" of clearance.
  11. 1967coronet

    Congrats to FBBO and Hawk Sorman Carlisle third place in club participation.

    Congrats Hawk and all you guys that made it happen. I would love to have to have gone to it.
  12. 1967coronet

    Happy birthday 1STMP

  13. 1967coronet

    Not a Mopar, but they're still out there

    That is great ! I like the color .
  14. 1967coronet

    Any later model Chrysler 300 owners on here ?

    Thanks for the replies, it us good to hear from guys that have owned them. We did buy a 2019 Limited Edition today with 52k on it. 3.6 , leather, alpine tunes, new rubber and very clean, good carfax , regular dealership service by the 2nd owner. It was a 2 owner with Enterprise being the...
  15. 1967coronet

    Engine rebuild toolkit. What's in yours?

    pnora gave you a good list, along with a good set of hand tools. I have to double stress the cleaning brush set. Never take anyone's word that it's done. Clean all oil passages your self then do it again.
  16. 1967coronet

    Any later model Chrysler 300 owners on here ?

    My wife and I had a very nice 16 LTZ impala limited we both liked the older ( limited ) impala body style. The newer impala body's have shrunk like most all cars. Like a dumb azz we traded for a newer equinox , only 24 k on it but we / I do not like it. We are looking a a few 2019 - 20...
Back
Top