• When you click on links to various merchants on this site and make a purchase, this can result in this site earning a commission. Affiliate programs and affiliations include, but are not limited to, the eBay Partner Network.

Search results for query: *

  • Users: HEMIB
  • Order by date
  1. HEMIB

    Since when does Edelbrock make a Holley carb?

    I have a Holley on my 340 it has all the standard Holley linkages it has made in Japan on it must have been under license .
  2. HEMIB

    WTB 360 Magnum Pistons

    Dish -5 cc, .030,Forged ,.984 floating pin, i beam rod ,3.58 stroke
  3. HEMIB

    How about just a random picture. NOT the entire car

    Holley Dash
  4. HEMIB

    72 Satellite Gen III Hemi Restomod

    Throttle body 53034251 AB set your timing down to around 14 .5 mine is at at 14.8 cruise starts to ping a lot at 18 ,from the factory Holley sets it way to high mine was at 35 cruise that will damage a hemi ,mine is making around 320 HP Rear Wheel ,192 KMH 3.23 5,800 RPM final drive on the...
  5. HEMIB

    72 Satellite Gen III Hemi Restomod

    Sounds like the memory wire is not connected to permanent battery power (Via a Fuse) normally red or yellow
  6. HEMIB

    TTi exhaust

    Has anyone got any pics of TTI headers fitted to a 72 Roadrunner Hemi 6.4 mainly around the Torsion bars & Power steering box ( have borgenson) the Hooker long tube fit like crap
  7. HEMIB

    WTB 360 Magnum Pistons

    you would think so but everyone you call no stock including Summit & Jegs,Campbell
  8. HEMIB

    WTB 360 Magnum Pistons

    Anyone know where i can get Magnum 360 standard stroke + .020 -5 cc pistons floating pin
  9. HEMIB

    Engine Noise - Video Attached - Thoughts?

    Try moving valve side to side up & down could be a worn valve guide
  10. HEMIB

    72 Satellite Gen III Hemi Restomod

    Have to do the same will use a 12 V timer should be roughly the same each time not big on the full up look
  11. HEMIB

    72 Satellite Gen III Hemi Restomod

    All good did the same had to add an extra washer to move the the bolt back a bit left some nice score marks on the back of the rotor
  12. HEMIB

    Oh $h!t moment - water tower takedown goes wrong

    Pay peanuts you get monkey's
  13. HEMIB

    Are You Demagnetizing Your Connecting Rods?

    We used to fit new bearing,s on the Deisel electric locomotives & used an induction type bearing heater to preheat the bearing for fitting ,similar to that magnetic flux crack to in the picture .You had to remove the bearing while the heater was still turned on with AC current flowing if you...
  14. HEMIB

    Pricks!

    Do you have a pic of the connector some of them a a MOLEX mini Jnr you can get from Mouser Electronics
  15. HEMIB

    72 Satellite Gen III Hemi Restomod

    The original studs heads are close to .2 of an inch
  16. HEMIB

    72 Satellite Gen III Hemi Restomod

    I was concerned with the bearing not positioned properly on the axle it may not have the bearing retained behind it if the bearing is not situated against the outside should it may move i would get it checked.
  17. HEMIB

    72 Satellite Gen III Hemi Restomod

    Have you pulled that bearing off the axle looks like it is not all the way on
  18. HEMIB

    72 Satellite Gen III Hemi Restomod

    Is there any contact marks on your discs if the discs & caliper are centralised (shimmed correctly ) there should be none if the axles are moving they could contact the caliper. All my trutracs groan from time to time when turning sharply
  19. HEMIB

    72 Satellite Gen III Hemi Restomod

    Do you have the circlip clamped on the differential face or further out oil can also make a difference with the tru track
Back
Top