Search results for query: *

I replaced my 727 with a silversport TKO 5 speed. I was happy with the kit. Clutch and brake pedals fit nicely but the brake pedal was much lower than the clutch when attached. Nothing I couldn't fix with my cut off wheel and mig welder. Would have worked but I wanted it to look right. The piece...

The best way I've found to grease the rear bearings once you've cleaned them out and blown them dry is to use a pencil point tip on your grease gun and go around the big end of the the taper and pump em full.

I had the same problem when I put a 11 inch clutch and bell housing in my charger. RobMC makes a great compact starter that solved my problems. You can loosen 2 bolts on it and rotate the solenoid and field assembly to any position to give clearance to your headers.

I like the turn buckle design. Made mine similar except I bolted a plate to the front of the block instead of the back of the water pump and used a sway bar link rod bushings on the bottom to provide a little cushion. It's a 512 stroker motor with tons of torque and a manual transmission that...

MoparMur knows what he's talking about. I've overhauled a few hundred automatics at the dealership. They all work basically the same. Some use vacuum modulator and kick down linkage to determine engine load others just a throttle linkage but either way it needs to be hooked up and adjusted...

That's the lower control arm bushing and it's bad. I tried the pst replacement bushing and shaft and didn't like it at all. The factory bushing is vulcanized into the outer metal shell. The pst isn't. Didn't take long, maybe 6 months and the pst bushing was squirting out the front side and broke...

I put a TKO 600 into my 70 Charger and removed the 727 about 18 months ago and I'm VERY happy. I highly recommend the pistol grip shifter. With some home fabrication to mount the shifter boot I was able to keep my center console. I have a lot of hot tips if you want to contact me. Like DON'T...

Looks great! I admire all the hard work. Are you in Oklahoma? I might have a few Mo-parts laying around near Tulsa.

Drove my 70 Charger an hour to work and another hour home. Just makes me feel good when I'm stressed out. Ate a ricer on the way to work. Tasted really good .

I'm guessing more like 650 hp and 735 torque. That thing is gonna breathe. Big exhaust will help. Like 2" primary headers and 3" exhaust. Enjoy all that torque.

I put trick flow 240s with a roller cam and taller valve covers on my 70 charger and have no clearance problems with my vacuum booster. I used the mopar performance aluminum covers which are fairly tall to clear my Harlan Sharp rockers.

Sorry, I said Hughes. I meant Harland Sharp. A bit pricey but worth it.

I built a 512 stroker for my 70 charger with a comp roller cam of similar duration and an edelbrock performer rpm and a quick flow 950 double pumper. I really the trick flow 240 heads. It is still pulling hard at 6000 rpm which means good flow. I went with the Hughes roller rockers. Be careful...

I used a couple of small yet very strong magnets placed next to where I was grinding and they worked great. Still re washed with solvent and compressed air and brushes. I like the shop vac idea too.

I know this is a B body and not an E but I had a 70 Barracuda with a drive shaft vibe I was chasing. One day I stood it up and I heard something clunk inside of it. I flipped it over and heard it clunk again. So the drives haft shop cut it open and inside was another piece of tubing with a...

Oh, and only use Spicer or neapco U joints. They are the only ones I get consistant balance runs with. Others have too much play in them.

Could be out of phase. To check it get a cheap angle meter with a little magnet on it. Put the car on jack stands under rear-end and outboard end of front A frames by the ball joints. Turn the drive shaft to where the cross of the u joint on the pinion flange is straight up and down. Stick the...

If you add just oxygen to the combustion chamber it will get so hot you'll melt pistons AND you will loose a lot of power because the expansion of the oxygen in the chamber as it burns is not much. With nitrogen also in the chamber the heated nitrogen expands WAY more than the oxygen. The...

It's either the forward clutch or the front planetary gear carrier or forward ring gear. Chrysler calls it the front annuls gear but same thing.

Used the Harlan Sharp rockers specifically for trick flow and Edelbrock heads. Perfect alignment and no problems. Ordered custom length pushrods from Smith brothers. No problems ayquick delivery too.