• When you click on links to various merchants on this site and make a purchase, this can result in this site earning a commission. Affiliate programs and affiliations include, but are not limited to, the eBay Partner Network.

Search results for query: *

  1. Nxcoupe

    What's it Worth 1968 charger RT 440 (Listed for 31k)

    I spoke to the guy that originally listed it. The trailer looks nice. If you see my comments under the ad, Michael Bruce, it's the same car.
  2. Nxcoupe

    The Mopar I never wanted...

    My condolences to the loss of your close friend. I race at KK ocaisionally too with my Fox race car. We are very close geographically and I'd like to meet you and see the car sometime. I, too, have a coronet 500, and it's red. I can't usually race at KK because the shut down is too short, last...
  3. Nxcoupe

    Is this right? Removing ball joint.

    Hind site is 20/20, you went about this in the wrong order. Now you're going to be replacing parts you didn't need to. 1. Loosen nut on upper balljoint under upper spindle mount. Take it out about 5 or 6 turns, enough that you can see a 3 or 4 thread gap between nut and spindle 2. Hit spindle...
  4. Nxcoupe

    Cruise Control Unit Rebuild

    I know this is an older thread, but Tony did you get these made and tested yet?
  5. Nxcoupe

    66 Coronet 500 Driver, Light Resto

    I like the looks of it, we'll see how it works and how visible it is when it's all mounted. I washed the bezel and cleaned the lenses with soap and water. They are a bit foggy but they look a lot better now that they are clean.
  6. Nxcoupe

    66 Coronet 500 Driver, Light Resto

    I will document that better as I get to it. Everything came from inline tube. I got the cool trapezoid booster and period correct disk brake master cylinder. All the lines are stainless steel and prebent.
  7. Nxcoupe

    66 Coronet 500 Driver, Light Resto

    I spent a few minutes while waiting on my wife to finish getting ready to take me out for Father's Day, to mess around with the tach I got. It looks good, has a provision for a light and is made of metal now. It was a straightforward swap. Looks good but a little hard to see through the tiny...
  8. Nxcoupe

    It's been a crazy week... Typical Friday the 13th...With a Cherry on top...

    Yep, I was polite to everyone but I'm sure my frustration showed some. If I felt that it showed, I apologized. They are just doing their jobs.
  9. Nxcoupe

    It's been a crazy week... Typical Friday the 13th...With a Cherry on top...

    Wow! What an adventure but you made it! Same with Kern Dog. About 7 years ago, I got a call in around April from Marriot offering me a 5 day, 4 night getaway to several cities, one of which was Orlando. I chose Orlando and picked the 4th of July weekend as that year it fell on a tuesday or...
  10. Nxcoupe

    66 Coronet 500 Driver, Light Resto

    Most of my stuff is Moog. Thanks!
  11. Nxcoupe

    66 Coronet 500 Driver, Light Resto

    Lower ball joint was in good shape, but getting replaced while it is apart. Upper is a different story, it's garbage. Tie rod end has no boot so even tho it seems tight, it's been exposed to the elements and is getting replaced. I got the nuts off the strut rod on both ends and all the tension...
  12. Nxcoupe

    66 Coronet 500 Driver, Light Resto

    After sanding my butt off on the wall where my porting bench is gonna go, I decided to get the coronet up in the air and inspect the fuel leak situation. It looks to be the rubber seal is leaking. Must be from when I reused it on the fuel pump module install. Oh well, nothing I can do about it...
  13. Nxcoupe

    66 Coronet 500 Driver, Light Resto

    Today it was really humid, and just nasty outside, so after applying mud and climbing up and down the scaffolding, I decided to come inside and paint the gauge needles. They really needed it. I put wax paper under the needles to keep paint off of the gauge faces and then shook the paint up. I...
  14. Nxcoupe

    Oriellys wiper motor new 68.00

    Wish you had a pic of what the hole looked like afterwards. Would a drill do the same thing?
  15. Nxcoupe

    FOR SALE 1970 dodge charger R/T

    Looks like 440 auto, 8 3/4 3.23, T6 with white interior and white vinyl top, power disk brakes, Tan/Gold interior with buckets with buddy seat/armrest, build date of Feb 20, 1970(Day after my Birthday), outside adjustable mirror, some moldings, std AM radio and a white stripe. Very cool car...
  16. Nxcoupe

    66 Coronet 500 Driver, Light Resto

    I started laying out all the parts for the brake conversion. I confirmed Steve sold the correct spindles to me and also that my 66 ball joints will work with them by comparing part numbers on Rock Auto. Bearings also work as well as calipers. Let's get this started!
  17. Nxcoupe

    66 Coronet 500 Driver, Light Resto

    Next, I turned my attention to the headlight switch, specifically the dimmer circuit. I bought some WD contact cleaner, and the jury is still out, I need to connect it all up and test it's function. The LEDs won't dim unless they have internal circuitry to pwm themselves according to voltage...
  18. Nxcoupe

    66 Coronet 500 Driver, Light Resto

    I decided another coat of 'chrome' was necessary, so I got everything ready and carefully added it to the main surround and to some of the smaller ones inside. I also touched up the corner of the E in Dodge. Not perfect, but much better than before.
  19. Nxcoupe

    Carlisle Tent Activities 2025 - Volunteers Needed!

    I was able to get on later that day. I am registered and legal now.
  20. Nxcoupe

    Carlisle Tent Activities 2025 - Volunteers Needed!

    I tried registering today and it kept timing out and giving me the white screen. Anyone else having an issue?
Back
Top