Search results for query: *

I also have a good 727 transmission and a Dynamic converters 727 custom built converter for this engine available. The converter cost 865.00 09/22 Willing to sell both for an extra 600 with the engine.

I have a 1970 340 engine with 680 miles on it since being rebuilt. This was professionally built by a well-known stock/super stock NHRA builder. It is a solid roller cam with Harland Sharp rockers. The one and ONLY issue with this engine is we made the decision (which I regret now) to not bush...

For some reason, I'm not getting notifications from this site. I'm on "For A Bodies" more than here. If you get to the point that you are in the market for them, check with me there. Good chance I'll have them still, no hurry to sell them, they are just sitting on a shelf. Thanks

Hey Tom, yes, I still have these. Thanks, I haven’t been on here for a while. Sorry for the late reply. To the op, if you are still looking, I have a new set of that helps? Thanks

I installed the aft metering blocks on mine with the newer-style fuel tubes. Allstate had everything I needed to accomplish this. They will have anything you need for yours. By the way, your car sounds great!

Give Jim or Jarred a call at Allstate, They made kits for my 660's that were missing the choke towers and for my six-pack carbs. They are great to work with. They have helped Andy Wood and Unity Motorsports Garage with his carbs also. Great guys! I have some 660's that I will be selling if...

I have a nice 489 case 3.23:1 dated 1972 cone-type sure-grip center section for sale. I have been running this in my car for the last several years with zero issues. The only reason I'm selling it is I've decided to stick with the 3.55's I have. The pinion snubber has been sold separately. I...

The air cleaner base was cut for air conditioning at some point and is not very noticeable when installed.

Additional photos

I have a very nice complete six-pack setup for sale. The carbs have been rebuilt, including new diaphragms. The fuel lines and linkage are complete. I have a spring kit for the vacuum pods. I did save all the old components for the carbs that were replaced. This includes the air cleaner...

I have a NIB small block Mopar Performance solid lifter cam and lifters kit for sale. Purple shaft P/N P4529973 Specs are in the photos. Asking 425 shipped in cont. U.S. from 80534. Will ship outside the U.S. for difference of actual shipping cost.

Still available

I have a very low use 489 Yukon 3.91 ratio center section. I believe it has the Powr-Lok sure grip clutch type diff. I have run this for a couple hundred miles after purchasing it from the previous owner. No issues at all, just too steep for my street car. Feel free to ask questions or...

Not sure, I’ll post a close up

I have a 489 case 3.55 Suregrip center section that has a whine while running I believe it is a gear whine. I purchased it knowing it whines. Original owner has been running it for a while and I installed it into my car and ran for a short time. No vibration or any other issues noted. I’ve...

Yep, there is a thread on fabo about 3.58. It’s definitely steeper then the 3.23’s

I have a 727 pan with a drain plug , it is a shallow pan. Approximately 1” deep. Asking 20.00 plus actual shipping from 80534.

8 3/4 Pinion snubber. Good condition Asking 35.00 plus actual shipping from 80534

I have a 8 3/4 center section ,741 case from a B-body car. The gears are marked 2070301-3.58-1. 9-17-62. I have been told it is a Power-Lok clutch type diff. I installed this in my car and ran it to 100 mph with zero issues. I removed it and installed the 3.23 back in. (Too steep for me). Asking...

Updated photos