Search results for query: *

I know guys it is not a mopar but my son loves his mustang. Many of you might have read the story but anyways I am having a little problem with the ignition. First there is a toggle switch to start the car. If you turn the key to start the start position it does nothing but once you press...

So I have been looking to replace the wiring under the dash and in the engine compartment and Year one is calling for a separate harness for the Tach but mine is all tied into the main block. Am I missing something or am I reading something wrong? Also I have converted to a mallory dist so...

My passenger side door window is sagging about a 1/2 inch toward the back part of the door so it will not seal. If I take the handle and press it a little it will go to the right possiton but will sag again as you let off. Is there any adjustment that could be made to fix this problem. I...

At one point I was having some cooling problems but replaced the radiator. All was good for a few months. Then one day it started running warm but them it would just drop to normal so thought a sticky thermostat replaced it and all good for a week and then the same problem. The water did not...

I just won the switch but missed getting the relay. Is this something that I can wire without it or is that not a good idea? Forgot to add its a 68 Superbee

So I installed my new carb, valley pan, a couple of other things, and getting everything dialed in. Now out on my test drive the car is running pretty good so I start heading back home and pulling into the driveway I start hearing tap, tap, tap look down and now oil pressure. I turn the engine...

I bought a new carb with Electric choke which I have not had before. I thought that you tied this in at the coil but it says not to do that and I new a keyed power source. Where have you guys tied this in? Also is there an easy way to setup the Idle mixture? I should just read the paperwork...

I bought a new valley pan gasket with a heat rise block off that comes with the paper gaskets also. My question is do I need to add any type of sealant to this setup of do I install it as is? Thanks Jim 383/727 68 Bee

Ok this is a MSD setup I got many years ago with an engine that I just installed in my car. It is old but was told it was in working order at the time. This would go in my 1968 Superbee 383 The problem is I do not know how to wire this thing up. If anyone has this or knows how to wire this up...

I have a 68 Superbee and just wanted to know if this will work or basically swap out? Thanks http://www.ebay.com/itm/271005148033?ssPageName=STRK:MEWAX:IT&_trksid=p3984.m1423.l2648

So after a few weekends installing my engine and rebuilt trans I finally was able to fire it up. I have a book on order for all of the timing specs so today I was going off how the other engine was set-up (383 1968 Bee). Before I pulled the engine I set it on number one comp stroke and marked...

I am installing an engine this weekend and has been sitting for sometime. It is free but I would like to prime the system before starting. I know that this has been discussed before and sorry for the new thread. I know counter clockwise with a good drill but am I just turning where the dist slot...

I would like to thank everyone here for all of the help to make this possible. My father has about a month or so left on this earth as he is losing his battle with cancer and he wanted a ride in his car. He bought it in 1970 and took it apart aprox 16 plus years ago to paint and so body work...

Ok so I started installing my headliner today on my 68 Bee. All is going good but I have one question................ By the back window as the headliner turns down the back window and the pop out windows, it likes like there were some kind of retainer that holds the middle of that part of...

Ok I have a 68 superbee (post) and I bought the wrong seals years ago not knowing that at the time. I still did not notice until I went to start installing them and saw "no post" on one of the packages. I had already put one on the door but did not seem right that is why I started looking a...

We need to have a rant section I think. Or do we? I have been working on my 68 Bees Gauges getting the new Rallye gauges installed and still after weeks of following wires and everything looks right it does not work correctly. All that I have working is the amp meter, oil pressure and temp...