Search results for query: *

In my Charger, someone put double female ended belts bolted to the transmission tunnel side. its odd and very confusing. would it be for a should belt also? i dont have a shoulder belt on the roof. These are annoying as hell and id like to replace with the correct buckle belts in the front, 1970...

I tried all the tricks everyone said.... at the end of the day i ended up with a propane torch and putty knife, followed up with a angle grinder and knotted wire wheel... It's just one of those jobs that sucks but have to get through it

ckessel and matthon, are you reinforcement welding the pivot shaft sleeve inside the k-member box? And, doing so aides in keeping the pivot shaft from turning inside the k-member and bushing when installed and torquing the nut to spec? With my k-member installed and both sides of my suspension...

This is what a stock hood looks like with a scoop ... meh !! Next is the bottom of my "6-pack" hood - might give you an idea. FWIW, it clears a single plane Indy intake on a RB with air cleaner. Would likely clear two carbs on a crossram. I have about 3/4" clearance on the top of the air...

Don Garlits Museum Tim Welborn's Muscle car Museum in Alabama St Augustine is very nice in the winter. I would Stay over on Anastasia Island . I personally think its a little quieter Been there dozens of times as wife has family in the area. There are some good restaurants and great sites to...

I’m finally getting my engine to the tuning phase. 440 six pack, mild cam, Promax outer carb plates. The engine runs great on the middle carb and idles well at 800rpm. However, when I open up the secondaries I’m putting out a lot of black smoke. I’ve got the jets & idle air restrictions set at...

OP, Were you ever able to find the VIN for the '70 R/T? My 'Avatar' is my '70 Super Bee (sold new in Idaho). Y4 auto as well. The photo was taken of my Super Bee in January 1971 (Ross Park, Pocatello, ID) by the first owner. The next owner purchased it in 1973 and kept the Bee for the next...

:bday::bday::bday:

Please show the new panels? What brand are they? PUI stuff is famous for leaving OEM features off of their products. I have several door pulls, and may even have a tan one.

I had a breast, skin removed. I have always had a thing about their coleslaw, both sweet and tangy. 8 piece original chicken, large mashed potatoes, large coleshaw, 35 bucks. Smile on his face............. priceless.

Nice car... LOL

Right ... about ... there !!

Iranian Rial so about $14.30. But if you exchange your USD on the black market then it’s about $6.00

Figured they might have a sale, thanks, I will wait a week and see.

I'm sure you have probably been before, but Don Garlits museum is an easy way to kill a day. Looks like it is 1 1/2 hours from Daytona.

I was assuming pampered cars that don’t get driven in snow or rain

Welcome Bob! Nice 65 you have there. Is that light blue or mint green? Both were popular colors. Similar story here. I always liked early B Bodies but never owned one. As I was nearing 70 I thought I better get with the program or I will be too old to enjoy it. I liked the looks of the 64 and...

I learned long ago with my Muncies using the newer synthetic low viscosity gear lubes with OEM type gaskets and assembly guaranteed a leaky trans. The machining of those older tranny gasket surfaces just were not designed for the thinner lubes of today.

Look like Fudd guns.

KFC changed about 3 years ago. Now it's way more greasy (as if that was even possible, but it is), there's more fatty material that makes the batter less likely to cling to the chicken, and the chicken quality in general has gone down noticeably. I used to be a big fan, but now about all I can...