Search results for query: *

Good day all.my output shaft seal is leaking i have the 904 71 Plymouth satellite.i know i can get 1 from National moparts in Canada,but to my surprise AMAZON HAS 1 Timkin # 7300s can anyone confirm this does it fit my 904,befor i order.thanks gents.

i have a chance to get some Mopar valve cover hold downs,do SB and BB share the same bolt size.thanks.

Good day all,I am looking for a tyranny mount,is there anything better now a day's have allways got an Ancor, but after having my Ancor engine rubber mount tear in half,kind of leary.also in the past had a problem with the bolt being hole in the mount too small.904 transmission.what you...

OK I got my throttle cable mod almost done,was very easy to do,I have a few tweaks to do and them paint.used my low rise throttle bracket no need to get any thing else.it can be done for very little money.

I want a throttle bracket for my 71 Satellite 360,so I can get the right throttle cable geology,I don't want to hack my org,will save that for the next owner.thanks .

On line PG CLASSIC, MANCINI,trying to get a new 71 sb 360 throttle cable 20 inches long.they booth list for BB 71 -74 WILL this cable work on my 360.thanks in advance.

What else would work outher than the factory retaining clip.cotter pin.

OK just installed the holley heat shield.i don't like angle the throttle cable is.i am thinking cut wear my finger is pointing and weld a piece of steel say 1 inch + the cable hold down.that should put the cable in a much better angle,right.i would like to hack if I may so lol an other throttle...

My 360 ran like a champ the last time she ran.i started her up for a minute on the week end normally I run it up to 2 grand for 3 minutes.i did not warm her up. Went last night to our cruise in as soon as it started I thought fouled plugs, so we went to our cruise yup something is not right,so...

Hi need some help,I just tried to fire up the A/C unit.will not start up nothing not even a Humm.so I started poking around and found in the picture there is a switch once I push it down it all works great, but once I let release it nothing.no reset button either. Any thoughts before I call a...

Took advantage of nice weather today,the Killmat went very well,Mopar the cat likes the carpet.

OK it's time for some suggestions on cam shaft.my build 360 30 over 9 2 1 speed pro pistons,340 j heads 202 intake,edelbrock rpm performer,650 vs holley,headers,electronic ing,2800 stall 355 gear.going to manual brakes also.i had the 280 477 purple cam in a 69 dart and had lots of pull and my...

Need to know before I order a M/C for my 71 Satellite, I want an manual/Disk M/C .it's a Doorman part number MCA 75817.THANKS FOR YOUR HELP.

My 71 has PDB,would like to know what all parts do i need to change over to MDB.Iwant more cam,i know a vaccum can can help with supply more vaccum,but.thanks for the help.

Will a 71 318 b body engine mounts work on a 70 a body duster with a 318,trying to help a gear head.

Could someone give me the part number to the 8 3/4 diff gasket,I like fel_ pro blue,all I can find are dark Grey.this is for the pumpkin. Thanks.

There not to bad,reusable lol.spent the morning pulling them out and Mancini went in.hope they can handle this torque monster.glad I had a chain on the left side.

never search for 1 befor who makes a good slip yoke this winter i am changing from 323 to 355 gear,so once that pig is out it would be a great time to replace booth u joints and my slip yoke.a few years back my local shop put new u joints and said my u joint is spinning, they put in a my new...

Does the xe 274 pull enough vacuume for my power brakes,me want more cam,I now have the 268 OK but I know it will work with more cam.built 360 30 over 9 2 1, 340 j with 202 valve, edelbrock rpm performer, Headman headers,650 VS. 323 gear, going with 355 next year.will this 274 work with my...

Hi guys I have an 8 3/4 489 sure grip clutch 323,now I am looking, for 355 center section,I have called Moser and they want to know what I have now axel spline count,pinion spline I think I have 30 axel and 29 yoke does it sound right my pumpkin is a oem unit.thanks for the help.71 plymouth...