Search results for query: *

I have a pair of single groove BB pullies. A stock one for the water pump and a 30% underdriven Moroso for the crank. Both are cleaned and painted, $55.0 takes the pair. Shipping not included

I have one pair of UNPORTED 915 heads for sale. They need to be freshend up but are in good condition. A good bead blast, cleaning, valve job and they are ready to go. Looking for $550.0 or best offer. Shipping not included.

I have one set of 2.14" int and 1.81" dia ext valves for sale, stainless Matl.. They are clean cut and ready to fit your Big block heads. $135.0 or best offer, a lot cheaper than new. Shipping not included.

I have (2) TWO sets of chrome Moroso classic valve covers for sale. Looking for $65.0 a set. Shipping not included.

7 Pairs of Comp Cams 829-16 roller lifters for Big block. These have low hours of use. They can also be sent to Comp for re build. $175.00 or best offer. Shipping not included

One complete picture frame trim used on the 69 Satalite trunk lid. No dings, could use a good polish. $100.0 or best offer. Shipping not included

One set of Liberty valve springs (P/n LAV-9100-16) used with a .590 flat tappet DC Mech. cam. Only 700-1000 street miles. $100.0 or best offer. Shipping not included.

One set of PSI Max Life endurance springs P/n CT-1572 ML. Used with a .750 lift roller. Also with Titainum retainers. Low hours. $125.0 or best offer. Shipping not included.

A 1968 Plymouth B body rear wire harness, New Repo never used. For 68 Road runner or similar. $125.0 , shipping not included.+

One Hooker 1 58 dia Header passenger side for E or B body, uncoated. $100 .0 or best offer. Shipping not included.

I have a 6AL box, propower coil, timing retard box and Dist. for $350.0 or best offer. Shipping not included.

One set of hooker 1 7/8s headers for b or e body, painted not coated. $175.0 or best offer. shipping not included.

Has any one done a conversion to a power rack & pinon setup ? Also how about a tilt wheel aftermarket conversion for a 69 with the in dash ign. sw.? They used to be available but they now all seem to be obsolete by the manufactures. i been out of the game for a few years but getting back in now...

Hi, I just replaced a mini starter in my 69with the type same mid 90s mini starter. Replaced the wiring from the relay and the relay to the starter. Cleaned the connections at the firewall pass thru connector, the ignition switch works. Checked all grounds and they are clean and tight. Oh-ya...

I am looking to purchase one of these Dual Distributors for an old Pro-stock recreation. This is the old crank trigger setup used in the 1970s. You can send me a PM with price and condition. Thanks!

Has anyone converted to use E-85 for Hi-performance use in a street car? I understand the corrosion issues and the 1.5 times fuel usage, but I wonder about the other required maintains. The car would have all of the required "fuel safe" components in the system. My reason for the question is the...

I found out the hard way that the Comp Cams Magnum roller rockers do not like high RPM's in a roller cam application. They have tight .0015-.002 I.D. clearance and no bronze bushings for the Shaft, this combined with roller springs over 350# open and the gall up on the shafts. So now i am having...

I was glad to see Allen Johnson win in PRO Stock with his Hemi at the Mopar Nationals. It been tuff for the Mopars in Pro Stock for a long time. Ron Capps Put his Charger Funny Car in the winners Circle again too.

just found this site, attached a few pic of my 69 Beeper. Its been a work in process since 1974. Regards DanTrap.