Search results for query: *

Hello all, The gas gauge worked in the past (though not well). Over the last 2 years I have done a lot to the car restoring it and now it is up and running almost 100%. However, the fuel gauge doesnt read at all and I have to carry a gas can for longer drives. I checked the grounds to the...

After building a high compression 440 and adding air conditioning, I upgraded to an an aluminum radiator and electric fan setup. I have the radiator that was in the car when I purchased it (67 Coronet RT) that I have now found out is not original to the car since the stamping is 4036927, not...

Hey all, I am finally at the point where the car is just about finished (well, finished for a moment as we all know its never truly done) and I need the parking brake cables/connector bracket that goes underneath the car. This is the cable assembly that connects the parking brakeand actually...

So, finally finished up installing my built 440 and kept having issues getting it to start...anyway, it looks like a few wires going to the bulkhead connector got damaged during the install. It was reconditioned years ago and looked at again when I added A/C and addressed the...

Hello all, I am almost ready to fire up everything, but as I install an MSD box on my 67, I am not sure what wires I need from the ballast resistor and I do not see a similar setup on the mymopar wiring diagrams I have found. It may help that my car's drivetrain had been changed to a mid/late...

After a long journey, I am trying to hook everything back up with the new engine in and it seems a few wires lost their labels (or weren't labeled at all) on the left side of the engine and I want to be sure I minimize making a mistake based on what I think I remember. Where would I find...

I am looking for a 33 tooth (yellow) or 36 tooth (red) speedometer pinion gear for my 727 transmission. Ebay sellers are out of those sizes and I cant find at the normal restoration vendors :-(

I am trying to figure out the proper setup/routing for the kickdown linkage on my 440/727 combo. I am not sure if the hinged piece faces the front of the engine or the firewall and how I should route the linkage pieces back to the 727. I can't find the pics I took before the original engine was...

Hey all, I have a 727 behind the 440 that is going into my 67 Coronet. The factory speedo never seemed right with the red drive gear (didnt count teeth), plus now I have 3.55 gears in the rear...I am running 15" tires that are very close to the factory in overall height. The 8 3/4 rear is from...

I am finishing up installing the new 440 in the Coronet and need to get the 400 out of the garage for space. I posted a few weeks ago, but thought the engine was a 383, until I checked the side and saw a "76" in the casting. I don't know much about the engine as it appears to have been swapped...

I am finishing up installing the new 440 in the Coronet and need to get the 383 out of the garage. I don't know much about the engine as it appears to have been swapped into the car a long time ago (well before the PO). It does need a gasket/rear main seal refresh (leaked from the rear but didnt...

Hello all, My car just got out of paint and now it's time to get new rims/tires to replace the very worn tires and rough Crager mags. I'm thinking torque thrust rims? On a stock 67 what's the largest tire that can be put on? I'm looking at getting new 15" rims and want to get the biggest...

Hello all, Its been a few years since I posted as this forum was helpful when I purchased my Coronet RT in late 2014 and dealing with some leaking and other issues I had at the time. in 2015, I did replace the trunk weatherstripping with what seemed like an exact fit (never leaked being...

Hello all, My friend is rewiring the 67 Coronet RT I have as the wiring was completely hacked up and I am adding air conditioning and upgrading everything while the dash is disassembled. As he finishes up laying everything out, he is confused by the "Barrel Connector" that attaches to the back...

Hey all, Finally have some money and got my hands on a large water jacket 440 block and want to build it up as a performance oriented street able engine. I called Mancini, Scat, and a bunch of performance Mopar builders in Florida and they all have Chinese made cranks/pistons/rods/etc...

Hey all, I have a damaged jack for my 67 Coronet and want to know which years (or part numbers) jacks would fit. I have the hook and flat base, just looking for the actual jacking mechanism and "pole". Not worried about being factory original, just that it works and fits in the factory side...

The speedometer in my 67 R/T starting acting wonky while I was driving the other day (I have linked a video below). While maintaining a speed, the needle bounces back and forth a few mph above and below the actual speed, while there is a ticking noise coming from the speedometer itself (you can...

Simply looking for any advice or recommendations from those who have had their car shipped. It looks like I will be relocating to Florida at the end of August and need to get my 67 Coronet (and my daily driver Hyundai Elantra) down there. Any info would be appreciated as I have set up a UShip...

Hey all, The 383 in my Coronet has always whined a little, but now it is becoming much more pronounced. I have powe steering, in case that info is helpful. It sounds a little bit like I have an whiny belt drive supercharger under the hood, LOL. The belts seem tight and only show some wear...

Please forgive my ignorance on this topic in advance :-) In the process of gutting my interior to put down a layer of sound deadening insulation (and then finding rust to deal with on the floor pans), I noticed that my shifter assembly looks very battered and rusted/rotted. Since my car isn't...