Search results for query: *

Hello everyone. Would someone have some pics of the transmission cooler line routing for a 66 B Body Mopar (66 Charger)? It is a factory big block car with a TF 727. My lines were missing (had rubber fuel hoses). I ordered new ones from Mancini but would like a general idea on how they were...

I recently received my mopar cop wheels from Stockton Wheels. I am impressed and disappointed. The wheels overall look nice and arrived in the estimated time. That's the good part. The bad part is one of them came with a nick near the edge of the wheel. It was not caused from shipping as the...

It has been a long process but I have some paint and my molding back on the car. It turned out extremely well considering it was done in a machine shed. We used single stage Utech Acrylic Urethane. The paint is like iron. I still need to go over it with the P1500 Trizact pads to remove the...

I know some of you are running 295/50/15 on 10 inch mopar cop wheels. It looks like everyone is using 5 inch backspace wheels. Wheel Vintiques offers the 10" mopar cop wheel in a 5.5 backspace. Will the 5.5 backspace clear the inner wheel house or is the 5 inch backspace the only way to go...

I know some of you are running 295/50/15 on 10 inch mopar cop wheels. It looks like everyone is using 5 inch backspace wheels. Wheel Vintiques offers the mopar cop wheel in a 5.5 backspace. Will the 5.5 backspace clear the inner wheel house or is the 5 inch backspace the only way to go? Thanks.

I have no idea what the official name of this retainer would be but I need one for the passenger side. I will try and upload a pic. Thanks.

Does anyone know what Dodge used for a tailight gasket on the 66 Charger? I am talking about the once piece gasket that went between the light assembly and the body. The one I had on it was white foam. It didn't look correct and appeared to have leaked or been leaking. Looks like a piece of...

Duplicate post. Please remove.

I am in the process of installing the upper molding that snaps on the top of the quarter panel. My question is do the clips snap on the quarter first or do they fit into the trim and snap down with the trim. It appears I have two staked in to the front of the short section of trim.

I am looking for the plastic bushing for the rotating headlights on 66-67 Chargers. I also could use the bushing/light housing support/pivot that the bushing rides on. (The part with two screws that is accessible from the turn signal housing location) Are these sold aftermarket for am I going to...

I am looking for the plastic bushing for the rotating headlights on 66-67 Chargers. I also could use the bushing/light housing support/pivot that the bushing rides on. (The part with two screws that is accessible from the turn signal housing location) THANKS!

Looking for a drivers (LH) rocker moulding for a 66 Charger. I understand the Coronet may be the same. Just need a driver quality piece. my passenger side is decent but drivers side is pretty beat up

I have a quick question. I recently found a different door for my 66 Charger. I think it may be from a Coronet. Is the vent window and drivers window the same as the Charger? It looks the same but I currently have the door off the car and now is the time to change it if need be. Thanks.

Any body have a decent 66 charger drivers door they would part with? If so how much? Thanks.

This is kind of a follow up to my earlier question. Do any other B body doors interchange with the 66 Charger? The GTX and Coronet look similar if not the same but I am not sure? This is my first early Mopar so please forgive my ignorance. I am weighing options on replacing the drivers door. It...

What are the differences in the 2 years regarding the doors. Do they interchange? Thanks.

I have a 1966 Charger with some minor rust. Floors, dash, cowl area, fenders all good. One quarter has a spot I need to cut out and the drivers door has a spot as well. Fairly easy places to repair. A couple spots have me concerned. Above the sail panel on the narrow buttress area between the...

Where would be a good place to find the hood letters for a 66 Charger? Someone removed mine and filled the holes. I am re painting the car and would like to reinstall them. The car will be a driver so they don't have to be perfect. I understand 66 and 67 are different. I can't seem to find any...

Hello all, I have a question. How do you get debris out from under the cowl area? I can see leaves and what may be a old vermin nest underneath it. I recently purchased this old charger and it has great potential. Just getting everything ready for paint and I would like to get that crap out of...