Search results for query: *

Help? Mike

Hi fellas, can anyone give me the thickness and OD of the distributor O-ring used with all the V-8 electronic distributors? I'm looking for a part that does not cost $15.00! Thanks. Mike

I have a rear wing from my 1998 Neon R/T to sell. I would like $50.00 plus shipping. Mike

Are any block hugger headers produced for B & RB engines? Thanks! Mike

I'm attempting to scrap a junk 1982 Chrysler air pump. I got the back cover off and the drive pulley. Can anyone tell me how the center assembly can be removed? Thanks. Mike

As I have sold my 6 pack car I no longer need the lifting fixture I fabbed to use. I would like $25.00 plus shipping for the tool. I use the 49349 zip code. Mike

Hi fellas, I am converting a 1982 Chrysler from Lean Burn to older style ignition. I have bought a conventional electronic distributor on E-Bay and I can't find any advance specs in my manuals. I appears to be a 1973 model, possibly form a truck? Thanks for any help! Mike

I am converting a 318 Lean Burn system. Need carb and distributor. I can rebuild if needed. Thams. Mike

Hi fellas, For some time now I have been selling economically or giving parts to other members here. I'm getting older and realize I can't build everything I dreamed of so, the part divesture. I recently sent off a steering column to a member for his grandsons' restoration and received this...

An old friend of mine asked if I could resurrect his Shelby intake system for a 302 Ford engine. I said yes! He purchased this new in the box over 40 years ago and only put 25 miles on it when new and then it sat. These were a "over the counter" item from Ford in 1966. It's a whole lot of...

Just wanted to remind you fellas to be more careful than I was when using tools. Last Sunday I spent 3+hrs in the local ER getting my hand patched up. I was cutting out spot welds on a fender and got too comfortable with the operation when I slipped off the weld. I went right into the web...

Hi fellas, I was looking for a new pair of rubbers today and stumbled on these parts. I have had them for close to 50 years so I guess it's time part with them! Mike 3- new intake valves for 340/360 with 1 7/8" heads and std. 3/8" stems. New Chrysler parts. $25.00 OBO. 2 new tappets (sealed box)...

My oldest friend is restoring a Road Runner for his daughter and is having trouble finding the seal "flap" for the glass? He has a metal strip with attached rubber seal (decomposing). Can anyone school me on this design? Thanks! Mike

I am looking for a pair of shut off valves for my fuel cell vent lines. I'm using 1/2" aluminum tubing for the vent lines. If I could shut down the vents while in the shop it would sure smell better! No luck with my search so far. Any ideas fellas? Mike

Hi fellas, The air inlet throttle valve on my DA broke. Has any one found a replacement part? CP has discontinued production of this little plastic item. KF124233. Mike

I fabbed this years ago to support my engine when dropping the transmission out. Thin wall tubing, 1/2" all thread rod, and 10/12 gauge strap. Of course, it only works with torsion bar suspension. A 2x4 would do the job too. Mike

https://www.atiracing.com/products/trans/transparts/superf.htm?utm_source=Mailer&utm_medium=PR_Blast&utm_campaign=Email Mike

I attended the Mopar show at the Gilmore Museum yesterday. I do not own a cell phone so, no photos. I helped a couple unload a custom-built trike shortly after arriving and parking (385 out of 448 entries). I saw it pull in and spotted something different about the engine so I had to...

These all need to be cleaned up but, all the steering joints are tight, all are usable. $250.00 plus shipping. PM me with any questions. Thanks! Mike

Since I sold my wagon I do not need the puller adapter either. I used it twice, I think. I fabbed it, blasted and painted it too. $25.00 plus shipping Mike