Search results for query: *

I need to change out the speedo gear in my 68 charger and dont know which gear to buy. Original gearing was 3.23's New Gearing is 3.55's Tire height is 27.9 inches. (285/35/20) At 70mph the speedo is reading 60mph .

Not mine, but came across a CH4B intake on Craigslist in Phoenix for $150. Thought I would share. https://phoenix.craigslist.org/cph/pts/d/phoenix-mopar-ch4b-440-intake/6871259324.html

Just did a twenty plus mile cruise without issue. Got on it plenty of times. I originally was thinking ignition because i never found what was fouling out the oe ignition modules before i swapped to msd. Something so remote and unpredictable like this, now i am thinking stuck float. Like i...

It has happened at various temps. Running 93 pump gas . Checked voltage at battery when running. Its at 15.3 volts at temp. Give gas then ket off and it went down to 14 volts. Gave it alot of gas and let off a few times. One time it dropped to 13vdc and the engine responded by running a...

Sight glass shows good levels. New carb installed before dyno run. How about timing? Could that throw it off. Timing is set at 25 at idle, and all in at 2400rpms at 38.

Were running a high flow mechanical pump. Its also brand new. Swapped it out on the dyno when the old pump was dropping down to 2 psi through the power band. Replaced the pump and pressure held steady at 6 or 7 psi. Cant remember exactly Yesterday i goosed it. Not enough to spin the tires...

Cruizing it never happens, but if i get hard on it, and let off, the ignition drops out. Atleast i think its the ignition. During its stumble, its not responsive to the throttle. Take it to neutral and start it back up. It might run a little rough at first but continues on perfectly fine. It...

I feel stupid, but I think I fixed the high idle. I went back and took a second look at the carb. The fuel log was barely touching the side of secondary baffle lever. Full throttle, it would open the secondary but the lever would get stuck on the fuel log. Let off the throttle and the...

Worked with Ron mid December to get a Firecore distributor and OE style ignition module installed. Took it to the tuner and put out 310/390 with timing at 25 and 38 at 2,400rpms. While on the dyno, we started having starting issues, and you could even see it on the plot curves. Prior to the...

Edelbrock Performer (1406) 600cfm carburetor for sale. Has less than 1K miles. Nothing wrong with the carb, just want to go with something bigger for my setup. The carburetor is still on the car and I take car for weekend cruises about twice a month. Planned on keeping it on the car until...

I have a complete set of windshield moldings with clips from my 68 Charger up for sale. No bends, twists, or dings. Minor scuffs but can be polished out by hand. $150 plus shipping via paypal.

I am looking for a transmission dipstick with the tube for a 68 Charger big block tranny.

I swapped out my 22" Champion aluminum radiator (4 pass) w/ a 26" US Radiator. Came off my 68 Charger. Wanted a more stock look. It's 22x21-1/2x3-1/2. Its a block style radiator that I added aluminum side strips to fit my core support. I also added aluminum braces across the front face to...

Check craiglist. I've seen various sets in various cities on Craigslist.

I don't need the radiator, but I could use the fan shroud. Would you be willing to separate, and if so how much?

Sal didn't have what I needed. I'm still looking.

I emailed you earlier.

Sal, I normally contact you first. Can you send me a photo to my holanae email account.

does it have a 26" fan shroud?

do you have a 26" fan shroud?