Search results for query: *

Good Day All!!! I am looking to replace my convertible top on my 67 Coronet. I was ready to commit to using cloth in lieu of vinyl. My wife's bow-tie Vett* has a cloth top and it looks so much better, IMHO, to vinyl. When discussing this with WNJ Interiors in Hatboro, they suggested, as a...

I have the back decklid/trunk panel (main piece) for a 66 Coronet 500. It is driver quality, with the usual pitting, decent, NOT SHOW quality. I have somebody who would like to buy it, cannot find any for sale on ebay for comps. I know the comparable pc for the 67 500 or R/T is worth quite a...

Ideally looking for one piece of trim for the back section of the rear console for a 66 Charger. It is the section behind the arm rest, it is approx 16 1/2 inches, stainless, 3 holes for fasteners and a little half moon which tucks in between the console and the bracket which holds the back...

I recently met a Dad and his teenage son. The son bought his first car, a 67 Coronet. We exchanged contact info. The dad texted me today, the son needs sun visor arms for his car. I have a driver quality pair. I cannot find any 'comps' on ebay or other used car part sites. IF they are only...

I came up short on 2 of the small screws which hold the three trim pieces that the boot snaps into. Anybody out there have any extra? I went thru my extensive stockpile of where-did-they-come-from fasteners and not doing well...Dan

Does anybody out there in Mopar land have any knowledge in changing a 67 Coronet from the traditional gas fill to a Charger flip top, locating it approximately near where a 69 Charger would be, on top of the left quarter? I was specifically wondering if a Charger gas tank would fit properly...

I closed off the left qtr gas fill on my 67 coronet and we are attempting to do the Dodge Charger/Challenger flip top on the top of the qtr. The filler tube I purchased used from a Charger is not working due to it's angle. We are still using the original entry position for the filler from the...

Good Day Mopar Brethren. I am looking for 2 bumper mounted turn signal assemblies and the lenses. I have one lens already, if somebody has a lonely one....Dan

I have a stalled project, bit off more than I can handle. I am looking for a Mopar Wrencher looking to make some extra money by helping me finish the mechanicals on my 67 Coronet. The engine is in, need exterior engine parts installed (carb, rad, etc.). Need 4 speed trans installed, have new...

Selling my 4 sp tranny. no issues, purchased OD trans out of my 67 Coronet 625 $ obo Willow Grove, Pa 19090 open to possibility of meeting halfway (within reason) can supply casting numbers (too cold out right now-burr)

Big Block Bell Housing 275 $ obo No longer available, still trying how to mark it sold...my apologies

I have a two piece arm rest. The bottom is situated between the bucketseats. The top pivots down to become the arm rest. If needed, I can drill out the welds on the brackets on top of the hump. 100$ obo

Looking for a 4 speed console housing for a 67 Coronet. I would prefer, due to my current financial situation (horrible) to try to modify my automatic to a 4 speed. They look identical, except for the drivers side cut out which starts JUST in front of the console light. I would gladly pay...

I need both rear panels for my 67 Coronet drop-top. Some heathen back in the Neanderthal days felt it necessary to put in two pair of speakers in each panel....thanks-Dan(the man)

Looking for an unmolested pair of rear drop-top panels. Also looking for the '500' emblem which came on a 65 or 66 coronet 500. They are gold, the 5 is notched in the back to enable it to fit over the 't' in coronet....

I am doing a light custom on a 67 Coronet Convertible. We have changed the gas fill to a 69 top side Charger. I am adding Super Bee Dual Side Scoops. I wanted to add 68 GTX lower side stripes out of grey carbon fiber, which I think will look great on black paint. I will finish it off with...

Good Evening Mopar Experts. I am doing a mild custom on a 67 Coronet Convertible, which will be black over black. I have relocated the gas fill to mimic a 69 Charger. I am adding the dual side scoops for a Super Bee as well. I love the dual lower stripes on the 68 GTX. I want to replicate...