Search results for query: *

This has been sold 9/16/20 @ 8:57AM

This has been sold 9/16/20 @ 8:57AM

I had to sell my 66 - and had acquired a center console that I never got around to installing. I still have the parts, but it is disassembled, bagged, and labeled. I am asking $250. I will ship it but it will add cost. I am in the Minneapolis area... Here is are the details of the packed and...

I had to sell my '66 but still have the center console, shifter, mounting brackets, wiring etc. I am asking $250.00 for the setup... I am in the Minneapolis area and will ship, but that will add cost.

Here the car running See all pics on my craig's list ad The car is located in Oak Grove, MN. I have had this car since 1996 and am looking to sell for a down payment on a cabin, my how priorities change. This car is a lot of fun to drive, with a 3500 stall and 391 with posi, 727 transmissions...

Selling a fully functional\upholstered front benchseat out of my 1966 Belvedere II. This will fit 1966 -67... From looking at other posts it sounds like it fits in up through 1970. $200.00 Plus shipping. This would ship from Minneapolis MN

I am selling the rear bench top and rear valance deck. $225.00 + shipping this is being sold as a set. Dimensions wise this will fit into 1966 B-Body's which is what I had intended but getting stuff ready for upholstery I changed my mind at the last minute. It would be shipped from Minneapolis MN

You both are great. Thank you so much. I did find the parts catalog and found details there too, between both I think I am set. Thanks!!!!

Thanks for the suggestion. I downloaded the 67 service manual, but it doesn't have anything for the track exploded view. I searched the PDF for "track" and "Seat" the section that seemed to have some information was located in the Body and Frame section. Is there another section to the site...

I had swapped out the bench for some buckets out of another '67 Belv. In my haste to get them torn down and restored... I did not stop to get any pics of the tracks and how the connect or left\right side. Can anyone point me to some good pics our instructions for the track assembly?

I wanted to update this post incase anyone else wants to test their fuel gauge. See pics.... If you use the reisistor, use a 6 ohm attach all 3 togethr then your leads to 1 & 2 = 6 ohms full tank then 1 & 3 12 Ohms than 1 and 4 for 18 ohms, or you can a 0 -100 resistor and test that way. I...

Kickdown lever I tried to get the lever from the tranny shop to work but the pin from the transmission wasn't tall enough to hold the bracket. I will try some salvage yards, and check Mancini's site to see if I can get a hold of one.

I bought the lokar kickdown cable (kd-2727ht) & the xsrk-4000 (bracket and spring) for my 66 Belvedere II 383 / 727 3spd. However I don't have the kickdown lever. I called a local tranny shop and they said they have a 3" lever that will work but he said my cable may not work and that it is...

It worked for me... Did you get all 100+MB of the zip? It worked for me I just now downloaded it and was able to open and extract files from the zip with no issues.

a

I am looking for some pic's of the rear seat area to see how\what brackets I need to make up to hang a different rear seat in my 66 as it has a full bench and am swapping the upper portion of the seat out... Any chance you can share some pics? Also not sure you saw I provided the info from...

I am looking for some pic's of the rear seat area to see how\what brackets I need to make up to hang a different rear seat in my 66 as it has a full bench and am swapping the upper portion of the seat out... Any chance someone can share some pictures?

The parts took 5 weeks to show up which had me nervous.... but they showed up and that part was in very good shape. below you can find where I got it from. I am looking for some pic's of the rear seat area to see how\what brackets I need to make up to hang a different rear seat in my 66 as...

I want to thank everyone for their input. I ordered the sending unit wire from evens wiring. I also came across passion4mopars.com site... Kim was truely awesome she has the very hard to find wiring harness for the the 66 mopars, and she make other custom harness too. If you are looking be sure...

I have not mounted yet... I will have to put in studs to connect it to, as my 66 did not have the fiberglass surround. I spoke to a buddy of mine who is a CAD guy and he thought he could design an insert that would say Belvedere.