Follow along with the video below to see how to install our site as a web app on your home screen.
Note: This feature may not be available in some browsers.
When you click on links to various merchants on this site and make a purchase, this can result in this site earning a commission. Affiliate programs and affiliations include, but are not limited to, the eBay Partner Network.
Waking at 3AM questioning my "brilliance" of yesterdays removal of the ballast resistor and replacing with a coil with the same resistance built in... is looking like "dumbass" instead!
69 RR 383 4spd. Upgraded to electronic ignition and trying to hide the orange box and new ballast resistor...
Hi, Have a low miler (47,000) 383 and have had some leaks into the valley pan. Upon removing and checking the intake fit to the heads, there is a .005 gap between the intake surface and the head on the right front and left rear...... almost like either the heads are not in parallel or the intake...
Not sure this is appropriate here, but certainly the people I might need will be in this forum.
Hi All, Been a while since I've been on, but believe I'm at the right place.
Own a 69 RR 383 4spd numbers matching. Had a little trouble with the lungs and have let the project go for some time...
Hi,
Looking for a Hurst 4 spd Shifter Ball for my 69 RR, 3/8 X 24 thread (fine). I believe the oem's were white. If you can help, please PM.
Thanks, trim
My Bad, Oem's were Wood Grain
Hi All, I need a passenger side lower control arm for a 69 RR/b-body with sway bar attachment. I have found a few, but most are bent, so I need a really straight one. PM me if you have one for sale.
Thanks, trim
steering column
Yes, you could extend the shaft in a power steering shaft but you cannot shorten a manual shaft for power. In your case, extending would mean that the lower bearing will still ride on the fat part of the shaft, so all would be ok. However, do you know how much of the square...
I now have 2 steering column shafts sitting in front of me. 1 from power and 1 from manual. They are not the same! I see where sliding the shaft up into the upper part will work, BUT, the diameter of the shaft where the bottom bearing goes will no longer be the same diameter. In that case the...
Hi, Looking for a power steering column shaft for a b-body 69 RoadRunner. Converting to power steering and need the shorter shaft. Actually could use the whole power steer setup including the pulleys and preferably a oem Saganaw pump.
Thanks, pm trim
Hi, Found it next to impossible to remove the plugs with a set of Hedman headers on my recent 69 RoadRunner w/383 4 spd. purchase. Since they got them in, I figured they would come out and with many unmentionable spoken words they did come out. I noticed that they had to dent the headers in many...
Thank you for the link. The headrests I'm looking for are different. I don't know if it's just the bench seat or if the difference is because of the deluxe interior option. Here is a link as to what they look like...
Hi, I have a nice bench seat, but need the deluxe type headrests for my 69 RR bench seat. I believe the 68's are the same, not sure waht models are the same???? Thanks, trim
Yep, to make it look purrrdy. New 69 RR w/383 for me. The ext. re=paint is good, the interior is an 8+..... but the engine compartment was the pits. Removed the engine & tranny for a re-paint of the eng. compartment.... the engine has recently balanced and has excellent compression.... They just...
Well.... almost hate to ask, as I'm sure the stupid label will be out, But, here goes.. I want to change all the visable bolts, Intake Man, lower head bolts, water pump etc.
If I take one at a time out and replace with new & torque, do you think this can cause a problem? Don't want to remove...