Search results for query: *

***Disregard... I dug through my stack of stuff, and found a pair. *** Color (if any) doesn't matter. Just not rotted. Like the bottom picture (w/opera windows)... Thanks

A little rust is fine, but no rot. If you're not local to NE Ohio, shipping would be to 44214 Thanks

These are relatively cheap, but aftermarket companies want a day's wages to ship them. Does any have a couple of these gas vent tube grommets floating around? 68-71 B bodies, and I believe the E bodies use them too. Thanks.

In search of (2) 15x8 or 15x8.5 steel rims. Big bolt pattern; 4.5” BS. Something like this:

Looking for shifter, levers, linkage rods and pedal assy for a 4-speed swap. Maybe even a 3-speed OD, if it's the steel housing (not aluminum) I'll also need a BB bell housing (2892513), but that will probably have to be local due to shipping costs. Thanks boys!

Looking for these rims with 4.5" backspacing in a 5 x 4.5" bolt pattern. Would rather not have unilugs. Hoping to find them within a couple-hour drive of NE Ohio, but may consider having them shipped.

Looking for decent (non-rotted) front and rear bumpers. I don't care if they're pitted or painted. Surface rust on the grill brackets is fine. Don't need the mounting brackets. Must be within a few hours of Lodi, OH 44254. Thanks. EDIT: Found the rear. Now just need the front

In search of a decent driver's side fender. Preferably in Ohio or a neighboring state. Dents and surface rust are fine, but prefer not to deal with rot.

Starting to gather parts for the 4-spd swap on the Charger. Anyone have one lying around?

In search of a decent driver's side fender. Preferably in Ohio or a neighboring state. Dents and surface rust are fine, but prefer not to deal with rot.

I'm looking for a 2-door A, B, or E body that was born with a 4-speed. From 63-74. It doesn't need to have the drive train, and I'm not afraid of a little rust. Just looking for a project with good bones, frame rails and cross-members. Preferably with a fender tag and within a couple hundred...

A friend of mine in searching for a project car... somewhere south of $7K. Somewhere within a few states of Ohio. Any engine and tranny. Thanks much!

Looking for a 2-door A, B, or E body with a floor-shift manual. From 63-74. It doesn't need to have the drive train, and I'm not afraid of surface rust. Just looking for a project with a good floor, trunk pan and frame rails. Preferably with a fender tag and within a couple hundred miles of NE...

Looking for an A, B, or E body with a floor-shift manual. From 64-74. It doesn't have to run... heck, it doesn't need an engine! Just looking for a project with a good floor, trunk pan and frame rails. Preferably within a couple hundred miles of NE Ohio. Thanks boys!

Looking for an original factory fuel sender lock ring for a 68 Coronet (probably the same for all B bodies that year). Bought the car with a repop tank and ring, and the ring is thin chinese crap that leaks.

Obviously not a B-body, but just a great looking car... I'm looking for a 1931-1934 Dodge coupe. Rough, rusty and ratty is fine, but I'd prefer it be mostly complete. Thanks for any leads you can offer.

I'm in need of the round connector for a non-rally gauge cluster on a '68 Coronet. I could really use a good unmolested harness, but I would settle for just the (female) connector.

I am in need of the upper right-hand piece of chrome trim (passenger side piece that covers one half of the roof and the C pillar. The other three pieces are good, but the fourth is a bit mangled, and wont snap onto the clips. Thanks fellas.

I'm hoping someone has two of these laying around. They slide into the rocker panel moldings on a 68 Coronet, and attach to the bottom of the fenders... to hold the front of the moldings down. Thanks fellas!

Hoping someone has this long chrome trim piece that goes above the instrument cluster and glove box on a 68 Coronet. Thanks!