• When you click on links to various merchants on this site and make a purchase, this can result in this site earning a commission. Affiliate programs and affiliations include, but are not limited to, the eBay Partner Network.

Search results for query: *

  1. Moparfiend

    727 & 904 Compatible Torque Converter?

    Are the torque converters on the 727 compatible with the 904’s?
  2. Moparfiend

    Guess the Torque Converter

    I am wondering what torque converter (diameter and particularly the stall speed) that may have came from the factory in my car. The car is: 1970 Plymouth Sport Satellite 318 originally 904A 273 peg leg originally Single exhaust (How did they get away with calking it a “sport” lol?) I assume...
  3. Moparfiend

    Bbody SB manual configuration

    What type of manual transmission and bell housing was used for small blocks in a 70 bbody? Would a 340 bell housing work with a 833 transmission? Was there a difference in transmission’s for sb and bb? Meaning was there an 833 for bb and a different one for sb?
  4. Moparfiend

    Yup Another PCV Discussion

    So I have read threads here and other sites regarding the value of the PCV system BUT I am not convinced or don’t fully understand the value for me in my application. Caveat, the environmental factors are not a consideration here. It seems the main value proposition of the PCV is that it aids...
  5. Moparfiend

    What does RB stand for on a 440?

    Whats an RB 440?
  6. Moparfiend

    Lobe separation and vacuum

    What’s the relationship of lobe separation to vacuum at idle?
  7. Moparfiend

    Speedometer cable 904 vs 727 same?

    Is the speedometer cable the same for a z904 and 727 with respect to the connection at the trans? Thanks MF
  8. Moparfiend

    Fouling Plugs ring issue or compression issue?

    Ok this is opposite of a 426 issue in that its for my 50cc scooter. But hey it’s an engine right? Not apparently burning oil in that no smoke in the exhaust is noticeable. Issue. Keep fouling my plug. I have a single 28mm cv carb that I’ve adjusted and think isn’t too rich (like me). Still...
  9. Moparfiend

    PCV Delete?

    Still trying to increase hood clearance and running into issue after issue. I currently have a spacer so that I can have a “proper” PVC connection from the valve cover to my manifold vacuum crankcase. If I need to cant I just vent this through a check valve to ambient atmospheric without any...
  10. Moparfiend

    Drop Base Air Cleaner Throttle Clearance

    So I need to use a drip base air cleaner for hood clearance. Welp the throttle linkage hits the base (see pic). I kinda expected this and am wondering what you guys do to implement a drop base air cleaner like this.
  11. Moparfiend

    Is it cost effective to cut down pistons?

    At some point I need to lower my compression ratio as well as re-cam my motor. Was wondering if cutting pistons (as opposed to buying a bee set) was cost effective given shop time and possible questionable results!?! Whats your opinion? I KNOW you have one
  12. Moparfiend

    Tight vs Loose Torque Converters

    So at times I have received recommendations on getting a tight and loose converter for say the same stall range. How does one specify a tight or loose? For example: Can I get a tight 3000-3800 TC and a loose 3000-3800 TC? What makes a TC loose vs tight?
  13. Moparfiend

    Are These Factory Rocker Arms on my 1973 340ci ?

    These look factory to me and not like my 318 stamped cupped rockers! But not familiar with the 340 set up. They look cast and fairly robust.
  14. Moparfiend

    Causes of engine dieseling or run on.....

    I have to kill my car (automatic) in gear lest I get dieseling. Wondering what might be causing this. I know its prevalent in high perf motors and I assume its due to high compression. If it is the high compression what is the mechanism that causes it? Is it just temperature and pressure? Why...
  15. Moparfiend

    Small Block Valve Cover Grommets

    It was very difficult to remove my old grommets on my 1970 small block valve covers. They were very hard and brittle. They weren’t rubber thats for sure. Does anyone know where to get replacement grommets for this application?
  16. Moparfiend

    Small Block LA Dip Stick

    This might seem to be one of those questions but I am going to ask anyway. Caveats: 1. I understand the length of the DS is dependent on the tube in which it sits. 2. I understand that when setting up a motor part of it includes correctly setting up the pan, the pump pick up and dip stick...
  17. Moparfiend

    Small block auto to manual transmission conversion

    Was wondering two things if I wanted to convert to a 4 speed: 1. what manual transmissions are readily available (including overdrive)? I hear stock 4 speeds are difficult to find. 2. what else will I need? Bell housing/inspection plate Flywheel Z bar and brackets Shifter...
  18. Moparfiend

    AFR Readings

    Hi, I have a simple question regarding AFR curve vs RPM’s. Does AFR typically read 5-7 points high (leaner) at idle than at cruise or acceleration? If my AFR is accurate and it may not be especially at idle I am reading 22 at Idle and 14.5 under acceleration or cruise ie higher rpms. I don’t...
  19. Moparfiend

    Dropping the distributor

    When I drop a distributor in an engine I have the rotor point to cylinder one. But this is just a custom for uniformity of wire location right? As long as the order of the wires is correct and in alignment of the rotor it does not mater which direction the rotor points. Correct?
  20. Moparfiend

    Cam variables that can affect detonation in a high compression engine

    Hey guys how ya doin? Now that you gave your honey her valentines gift and dinner its time to get back to reality lol. I have two questions: 1. What variables can I use in cam shaft selection that can help soften the effects of detonation in high compression motor? 2. If I am running a 12:1...
Back
Top