Search results for query: *

Anyone know where I can find a horn ring for a '67 Coronet 500, 2 door hard top that has been redone. Or where I can get mine done. I believe it's called a half ring , it doesn't go all the way around the wheel. Thanks, Dave

Anybody happen to have one they might want to part with in their parts box?

Will any of you guys give me some help on heads for my '67 318. It has any Edelbrock alum. intake and 500 cfm Eddy. carb. I have 2 650 cfms if one of them would be better. There is a Comp Cam #20-221-3 in it, valve lift .447 .455. The more research I do the more confused I get. Would stock 308...

Am going to put the engine back in my 67 Coronet SB today along with a torque strap. My question is, I have the base mounted on the K frame, so do I have to put the engines back on the mounts before I install the rest of the torque strap, or can it somehow be mounted either on the block or K...

Hey fellahs, I have to put in a new TC, a 2000-2400 stall. I started to pull trans. from underneath, but now am thinkin I'd be better pullin both motor and trans. out of the car in one peice and setting it on the floor. Wadda you guys think? The car is a 67 Coronet with a mild build. Mostly cam...

Hey guys, My 67 Coronet auto,318 is mostly stock except for a 650cfm Eddy carb, an aluminum Eddy intake, along with a Comp.20-221-3 cam. The current TC is whatever came stock with the car. Since the new cam it is really a dog off the line, much worse than before the new cam. I am not expecting...

I bought these off Ebay and the description says they are glass protectors on many B bodies, including my 67 , 2 door HT, Coronet. Says they go on the quarter window regulator. I got them because I have my back windows out and wanna put them on. Thanks, Dave

Anyone know where one of these can be obtained? It's a sleeve nut from the right rear quarter window regulator on my 67 coronet.

Anybody got a working rear quarter, manual window regulator for a 67 Coronet hardtop they would like to sell?:head_smack:

Anyone know the procedure for removing the rear seat window(drivers side if important to know that) and hardware from the car? '67 Coronet 500 two door hardtop. The window gets about 1/2 way up and the mech. starts clicking and jumping and I have to help it up the rest of the way.

Just in case someone who may have one and missed my request, I am still looking for the letter E on the hood of my 67 Coronet. Thanks

:sad10:Anyone got the letter "E" or the whole DODGE word for the hood of a '67 Coronet 500? One of the other guys on here is looking for me but he's not too sure he has any.

When I change the SB 318 in my 67 B body to a BB 383 will I have to change driveshafts along with the trans?

Can anybody tell me if this cam, along with alum. Edlebrock intake, and 650 Edelbrock carb will do much for my 318?

Anybody know if there is a rebuild kit for a 1967 Coronet, PS, SB, steering column. I made a bushing from a piece of PVC. I'd like to replace all the bearings and whatever else is in there. Haven't found a kit yet. Thanks, Dave

Put in a new cam and cam bearings in my 67 318 and since it was late fall and the car was already apart I decided to put an electronic ignition in it, a Proform. Used old coil and suddenly it started leaking oil. I'm not sure if I maybe hooked something up wrong or if I should have changed to...

Anyone know where I can get a new 1 wire switch? All I really need is a gasket for it but can't see that happenin. Sory, it's for a 67 727.

About a year ago I set out to make my gas gauge work on my 67 Coronet 318. First came the fuel sending unit at the tank, the tank was pretty crappy and beat up so I replaced that along with the fuel sender. Grounded it X2. Put in a new aftermarket circuit board in the dash, new voltage limiter...

Need the letter E for the hood of my 67 Coronet. Hopefully with both studs on it. Anybody got one?

Hey guys, I want to put alum. heads on mh 67 318 Dodge Coronet. I already have an Eddy intake. The engine is bone stock, soooooooo Do I have dick with push rods or different valve and stuff or can I bolt it right on. I already have new rockers arms on.