• When you click on links to various merchants on this site and make a purchase, this can result in this site earning a commission. Affiliate programs and affiliations include, but are not limited to, the eBay Partner Network.

Search results for query: *

  1. 493 Mike

    70 Charger ignition switch wiring

    I think the cheapest puller you can find will do the job. Mike
  2. 493 Mike

    Starter hitting the headers

    Is the header set meant to fit the 383 as well as 440? Don't be shy about "denting" the tubes. It is only cosmetic damage and won't affect power output (unless you go crazy with a hammer). I have used MSD starters on Dougs and TTIs without problems. Mike
  3. 493 Mike

    70 Charger ignition switch wiring

    Yep. Pull the steering wheel and keep digging. You may have to pull all the wiring from the column. Do you have a FSM? Mike
  4. 493 Mike

    O2 Bung for Oxygen Sensor Position ?

    Good spot. Mike
  5. 493 Mike

    Trans tool question

    I realized that and tried to delete my answer but, couldn't. It does do a good job if the VB is out though. Mike
  6. 493 Mike

    Trans tool question

    I use a large cap screw and nut with a couple of flat washers to draw the seal into place. Mike
  7. 493 Mike

    1968 Charger, Ray Barton 528 Hemi, Pro-touring.

    Check out this post: Cranky Post #3 Oct 7, 2022 Forum: General Mopar Tech Discussions
  8. 493 Mike

    1968 Charger, Ray Barton 528 Hemi, Pro-touring.

    Is the speedo pinion adapter installed per the tooth ranges cast on the face? Do you have a good ground at the fuel sender? Mike
  9. 493 Mike

    Door panel clips

    I'm using the sheet metal type on my 65 build as the upholsterer swears the wire loop on the frog leg type will show through foam padding, he likes to use. Mike
  10. 493 Mike

    Got rid of the mineral spirits in my Saftety Kleen vat finally....

    I have been using Safety Kleen in my wash tank for maybe 40 years now. They take the old, clean out the sludge, and pump in the new. I don't change it very often as I do not rebuild transmissions like I used to. I changed the solvent last year and the previous batch lasted 14 years. At $600.00...
  11. 493 Mike

    Broke the pilot drill bit for a 1/2" hole saw, need replacement

    You should be able to buy one at most hardwire/big box store. It they are too long a cutoff wheel can fix that! Mike
  12. 493 Mike

    Plastic or insulation preference

    I like the plastic. I cut mine to just fit inside of the panel perimeter, taped it on the door and marked all the necessary holes, removed the plastic and punched out all the required holes. 3M weatherstrip adhesive works well to retain the plastic. My 65 had slots along the bottom and the...
  13. 493 Mike

    Transmission problem?

    Brain fart. Mike
  14. 493 Mike

    Transmission problem?

    Is it filled with fluid? Check to see if the flex plate is bolted to the converter. Mike
  15. 493 Mike

    1967 coronet

    The Dougs headers I bought for my 66 Belvedere fit like a glove. Mike
  16. 493 Mike

    Current Rock Auto discount code?

    Help? Mike
  17. 493 Mike

    Oversized O-rings ?

    Try McMaster-Carr. Mike
  18. 493 Mike

    Distributor O-ring dimensions?

    Thank you! Mike
  19. 493 Mike

    Distributor O-ring dimensions?

    Hi fellas, can anyone give me the thickness and OD of the distributor O-ring used with all the V-8 electronic distributors? I'm looking for a part that does not cost $15.00! Thanks. Mike
Back
Top