Search results for query: *

Curious about pros and cons…. Didn’t know BendPak were made in china

Anyone install the shorter E body pistol grip shifter in their mid 60s B body non console car? Is it too far to reach? Pros? Cons?

Can someone post pictures of where to mount the rear view mirror & visors on a 68 Charger? I had a new headliner installed, and no clue where the holes are!!!

my 68 Charger has outside chrome trims with felt, which touches the door glass going up and down. Is there also supposed to be “inner felts/trim on inside of the glass? If so, what are they called and where to get? Thanks in advance.

On a 1968 charger with 440 4 speed transmission, getting ready to actually drive this car. Got motor running, found first gear, found reverse gear, when I let the clutch out, it engages half inch off the floor, which is way too low for me. Also sitting in driver seat looking at the shifter...

Considering a 4 post and found these within budget…. wondered if anyone out there has either?

I’m trying to find for the front door panels, the chrome piece that separates the upper and lower door panels. I have the rears (see pic). Upon searching im not getting results do to the fact im not naming them correctly?

I’m trying to find for the front door panels, the chrome piece that separates the upper and lower door panels. I have the rears (see pic). Upon searching im not getting results do to the fact im not naming them correctly?

Ive been wanting a 4 post lift for some time…. but my tiny garage has low ceiling. Im wondering if anyone has this same situation but did get a 4 post? I’m looking to see if I can only raise 3’, is it worth it?

On a 68 charger with factory buckets, the seat backs lean too far back. Mine have no “adjustment “, and i need a more straight up seatback for my back. It rests on 2 pins when in position. Any tricks/fixes out there for a more upright seat back?

If stock alternator on big block 68 Charger needs replacing, what should i be looking for amperage wise? I dont want to “cook” wires-seems like most new are 100 amps or so. I assume i need one for external regulator?

For 68 Charger with current power front disc and rear drums, looking for recommendations on a master cylinder & booster with correct pedal linkage….currently has this setup, which leaks from the output ports no matter what i try…

For 68 charger, 440, with A12 hood. Looking for ideas/pictures? For air cleaners under this hood?

Not sure, but its looking more and more like i got the wrong carpet…. (Came in a box when car was purchased). Aside from being in a box for 12 years, i tried like crazy to get rid of all the folds and creases to no avail. Steam, heat gun, nothing worked. On top of that, i cant figure out why...

I’m assuming there are seals supposed to be attached to the vertical chrome piece on front window, to seal both windows? Not sure what they’re called so i can search and purchase…. Thanks

Getting closer to installing new legendary rear and door panels…. Can’t seem to get thru to Legendary.. I see there are 3 possibilities for rear panels and door panels… First picture they come 7/8” or 1 1/8” overall length? Seems like the longer ones are too long for rear panels? The second...

Brand new distribution block leaks from the top fitting-see pics. I removed the top fitting and replaced the “crush washer”from Napa. STILL leaks, not a lot but leaks. I called a supplier (the right stuff) asked if they had replacement washers, as the Napa was not perfect size, but said they...

Been searching for pics of a charger with the vinyl top moldings on, but no vinyl top….

I HAD a thread in parts wanted…. This guy sent me a private message with an email address, (i was too dumb to write his name down, probably cuz i didn’t expect a scammer here)… He said “contact this Kathy, her past away husband was a forum member, and has your parts”…. I sent the email, she...

68 charger, came with a new aftermarket bumper. Was proceeding to install, and both left and right “ears” (the short elbows that wrap around to the sides) start rubbing the fenders? Knowing nothing about bodywork, can the “ears” be slightly bent outward about 1/2”?