Search results for query: *

1972 Plymouth Road Runner RM23, 400, 4 speed car. Much restoration over the last 4 or 5 years. Extremely nice and straight, rust free, super clean car. 1 of 906 4-speed cars, date correct 400 with fresh rebuild 10:1 and runs strong. Sure grip 3:55. Matching Trans. Dash VIN and Trans match...

About 2 or 3 years ago at most, I bought Sail panels for my 71 GTX from Legendary. They were completely finished and all you had to do was snap them into place. I believe there was just 2 fasteners that went back in. Fast forward to now. I bought a set for my 72 RR. With the perforated...

Looking for 1 RH Pass side exhaust manifold. Needs to be in nice condition with no cracks or heavy pitting. Don't care if it still has heat riser assy. 2899879 3751071 3769207

Looking for clean ones that don't need repairs or have excess pitting in them. Pass side 1071 preferably want the later one without heat riser Thanks.

Does anyone else have this product installed in their car? I have a 72 RR 4 sp (GTX gone!) that had this kit installed. My real question is whether this kit limits the amount of turning circumference? I have a hard time turning into a driveway and have to let the other car go first. Y turns...

Looking for the complete left and right assemblies with Lens or even just the Lens. But no cracked Lens. A nice set of complete assemblies preferred. Thanks!

Looking for very good condition with no dents etc. Don't care if it's polished. Thanks

Looking for one in excellent working condition. Also an antenna with good/solid condition connector to radio. thanks

Mounts in the rear of the console. I think Ebody's use the same console? Don't want the "new" chinese stuff. Don't need the the bezel, but will take the whole assy if you don't want to separate and it's in good shape.

Does anyone know of a 71 GTX registry (besides Govier) or 440+6 registry (71) out there? Just curious. Thanks.

Needs to be for the factory original studs. Need about 6.

Ok, I'm stumped. Anyone know a source for 3/8 washer hex head screws? The kits out there (if supplied by SW Productions) have incorrect sizes. They have acknowledged this. All the kits I see on vendor sites, look identical and it's real obvious that they don't contain the correct long ones...

I just need one of these. Anyone have any they can part with or sell?

This is the L shaped bracket that the hood release rod goes through, so it doesn't dangle....like mine!

I see that many people carry this L shaped clip that slides into metal bracket on door panel and the criss/cross spring portion pushes into the hole on door. I noticed one vendor shows them at 13/16th inch in height. So it made me think...I measured my original ones and they are definitely 1...

I'm looking for the brace/bracket that the pull down rod goes through. Thanks!

I'm done with these guys. I've ordered alot of stuff from them in the past. Their customer service has gotten worse and worse. Don't know about you guys, but I'm sick of the Covid excuses etc. Waiting on the phone for an hour every time I call is not acceptable. Pay your employees a half...

71 GTX 440+6 with Saginaw pump with cooler attached. Mine seeps very slowly I think from the case. Otherwise works fine. I hate leaks.....Can anyone recommend a basic seal repair kit? Rockauto one ok? I'm guessing it doesn't matter that it has a cooler attached to it? thanks!

This is not so much an electrical issue as it is mechanical in nature. I bought a Tuff Stuff 130 amp Chrysler Alternator. It has a pressed on pulley. Otherwise I would just switch out pulleys with the old alternator (which was replaced at some time). But not sure that would be a fix. The...

71 GTX. 440+6. Stock build. Total Street car. No track for it. When I run the timing light, I get fluctuations of 5 or more degrees in both directions, non stop strobing the time plate. RPM's on digital readout move up and down a little, but not bad. 50 or so. Initial is around 13 and...