Search results for query: *

Looking for a 69 Coronet RH headlight bezel. I will strip down and repaint so as long as it is in good shape with no major scratches and dents that is fine. Shipping to Raleigh NC.

Getting ready to “restore “my 69 Coronet tail lights. Not looking for a concourse restoration, just something that looks nice for cruising around and an occasional drive-in car show. I have thoroughly washed with soapy, water and nylon brush the entire assembly. Car was very very sloppily...

Finally, getting around to starting restoration on some trim pieces for my 69 Coronet. Originally a 440 package, but I will be doing a Super Bee clone. I need to strip the black paint off, clean and repaint in the correct design for the super bee. First question, what would be the best way...

I have a stock K member with LCA’s and 8 1/4 inch rear end with axles out of a 1969 small block dodge Coronet. K Member is in good shape, but I did cut the two struts to get tension off so I could remove the front suspension. The rear end is in good shape I believe but two pan bolts were...

Reinstalling the new rear end and suspension. New 8 3/4 rear end from Dr Diff, new heavy duty springs/bolts/front hangers/rear shackles from Mancini. Reusing my lower spring plates from my original suspension. It was a 318 car. Seems like the lower spring plates are too narrow. See picture. Are...

I’ve read numerous posts about the gasket but not one matching my senario. Just received a new housing/ 8.75 rearend from Dr Diff. It has the new green sealed bearings installed on the axles. Does the supplied gasket go b/w the housing and brake back plate or b/w the brake back plate and axle...

Looking for a front bench seat for my 69 Coronet. Really just need the frame but if it’s already covered, that is fine. Would love to have one with headrests similar to picture. Thank you. Bonus if it has a fold down armrest similar to second picture.

Good evening, I have finished restoring and assembling my steering column (69 coronet). As you can see from the picture, I have too much of a gap between the steering wheel and the housing. So much that the horn roller that makes contact with the ring on the back of the steering wheel isn’t...

Anyone have any ideas how to “darken” the letters/numbers in the clear plastic indicator? Unfortunately, they are smooth, would be much easier to freehand if they were raised. I’m afraid I wouldn’t be able to freehand it and have it crisp and not look homemade. Obviously painting the back white...

I may be being cheap and that’s OK if you say that I am. Trying to figure out if there’s someway to restore these items versus spending 100 or 200 bucks to get replacements. Mine are rust pitted a bit. Would it be as easy to Sand down, spray with etching primer and a chrome paint or would it...

Any interest in a complete (minus carb) 318 out of a 69 coronet? I don’t know much about it but it does rotate freely. Also have a 904 trans with converter from same car. Located in central NC. Apex, NC. Asking $500 for all. Make offer

Good evening, I have a question regarding the driver side versus passenger side door latches. I did a search and saw a thread similar, but didn’t have any answers. You can see on the red circled areas the differences between the two. Seems like this may be common on one side versus the other or...

Quick question, what are these moldings called on the rear of the 69 Coronet. Both of mine have been removed ( I have them) and getting ready to start the bodywork. Looks like they are held in place with inserts that go into the body. I need to find a source for the inserts to replace, but I’m...

Looking for a pair of original lower door hinges for a 1969 Coronet

Sentout my door hinges to Leo to be rebuilt, he is rebuilding the upper ones, but the lower ones are worn beyond rebuild. Obviously I’m having a hard time finding some original ones to have rebuilt so looks like my only option is going to be remanufactured ones from a store. I know the metal is...

Good evening. I’m about a month away from sending my car out for body work and paint. Doing an A12 tribute so I want a fiberglass lift off hood (it will be pinned of course). Anyone ordered one recently and what company offers good quality ones? Thanks, Ryan

I just purchased a used 1969 rallye Dash frame. I want to sand/repaint before assembly. Going to be using original black. Wondering if anyone knew exactly what color and tint/Finish(satin/flat,etc) was original. Thanks

Good evening everyone, I hope you had a great Christmas and New Year’s. I thought I would stop in and introduce myself although I have already asked a few questions on other forums here. My name is Ryan (RJBSJ in the forums) and I live in Apex, North Carolina. I recently purchased my first...

Good evening, hope everyone had a great Christmas. So I’ve been looking for a restored complete rallye Dash but it looks like they may be out of my price range. My car was a 440 Coronet and I am building a super Bee tribute. I wouldn’t have too much trouble spending the money if it was an...

I’m looking for a Complete Ralley Dash with gauges and switches for 1969 Coronet.