• When you click on links to various merchants on this site and make a purchase, this can result in this site earning a commission. Affiliate programs and affiliations include, but are not limited to, the eBay Partner Network.

Search results for query: *

  1. 12icer

    You're opinion on OEM or aftermarket valve cover

    I still have the 1967s on my 67 R/T and never crush the gaskets. They have the original heater hose loop too. I have a set of cutout blue steel and clips to adjust lash with.
  2. 12icer

    $500 1970 Charger

    Those original vin plates, radiator support ETC and the fender tags are the gold in them thar junkers.
  3. 12icer

    Failed Smog !

    The idea is to introduce air into the mixture, a silenced vacuum line will do the job it will have to be run through the firewall into the car like a heater control hose and open, it will be open just enough to pass without making the car run too rough you may have to turn the idle to lower the...
  4. 12icer

    What winch are you using on your car trailer?

    You can get overkill on a winch for light duty work, I had an 8000 pound gear reduction warn on my boom truck till the bearings wore out on it it had a four line dual pulley system on it. I picked up a 6" thick steel reinforced concrete 42" culvert 5 feet long with my boom truck and loaded it...
  5. 12icer

    What winch are you using on your car trailer?

    The tractor supply one in post 2 with a double line pulled a 1985 Buick Lesabre with a locked rear brake and four flats on my trailer I just pulled for a minute and let off for a minute just to be sure it wouldn't get too hot it was 10 years ago and it is still going after a lot of the same...
  6. 12icer

    727 Not Shifting Properly Now

    I found out the hard way that a torqueflite will break the clutch pack spring, push it through the lock ring and lock the clutch engaged. Glad you had the easy fix. Nice car BTW!!!!
  7. 12icer

    440bb 40psi cyl6 not firing help!!

    If it were my call I would pull the heads two cylinders side by side with low compression most times is the result of a head gasket leak or crack. As for shims I never use them if you have a problem in the geometry of the valve train you are using something not correctly installed or adjusted...
  8. 12icer

    Repop 67 dash guage bezel

    Mine is good the gages are faded but they are still pretty good going to run ‘‘em like they are the console tac is not right anymore but I have a small one under the left of the dash that’s right. The quality of repops seems to have taken a turn for the worse in most everything even some of...
  9. 12icer

    SOLD 1968 J Code 68 Plymouth Roadrunner.

    You may want to call someone in an old race car stable with the VIN you have. Did it show to ever have a Fender tag or was it not a production car? Do you have a line of ownership? .........................
  10. 12icer

    How does the Hemi compare?

    I would go for a conversion if I drove the car as a daily driver but as an occasional out and about driver I would just work it over right and use the right parts to make it right. I have a dozen B and RBs and If you build them with Fel Pro gaskets seal the threads where they need sealing and...
  11. 12icer

    440 misfire when hot curising

    I'm with 67 Coronet pull he plugs and have a look. You may have a small insulator crack that opens after it warms, and if you have a few miles on it you may be able to color read them. I would think it is leaning though and stumbling you may be running along with the throttle just at the...
  12. 12icer

    Post Your 13 Second Combos

    67 Coronet R/T 3890 pounds full of gas and me. Street raced many times 13 and some change on the stopwatch @ 110 to 120 3:23 rear, 68 440, every part match balanced on drug scales, w 67 HPs cleaned and opened up, 308D x 495L 2 degree advanced Allied, 800 Holley race built on Eddy port matched...
  13. 12icer

    Hurst Competition + Shifter Question..

    The Hurst competition plus is made for many vehicles BUT it comes with a mounting plate specifically for the application AND in Most cases Specific handle (stick) for the Application. Have you matched your trans application to your car? There are a few differences in some of the New Process...
  14. 12icer

    3BBL

    The 1050 I had did okay but I put it on where I had a 850 double pumper I had cut the choke tower off, put two rios on and spray tube orfice set them , hogged, zip tubed, vent baffled 4 corner jetted and put a 4.5 power valve in it with the 310 SS solid. It was like having coil springs launch...
  15. 12icer

    3" exhaust opinions?

    For a RB with built heads, 300+ cam, pistons, rods, a good fuel setup and some serious flow 2" stainless headers, 2.5 stainless exhaust H pipe at the right place and good quiet mufflers. If you want less pressure go for the 3" mufflers and back then oval the tailpipes to past the bumper. Good...
  16. 12icer

    TTI Exhaust fitment issues (AARGH!)

    Sounds like you got it all right the original H pipe on My 67 R/T only had a little more room than the tailshaft housing needed to hang it on there when you were stabbing the trans. I trial fit everything on the ground and measure the spread before trying them just a very small rotation can...
  17. 12icer

    Sister is still working on her 68 Charger

    Sis has been at this since I was a young man, I gave her the 68 for her 16th birthday. She has been through two restoration jails and two more take 10 years to do anything places, I cant seem to find time to get My 67 R/T back together much less fix her car. She is trying to find a back...
  18. 12icer

    New member finishing a 67 GTX

    Great car wish I could find the time to finish My 67 R/T it has been sitting for 8 years. Drove probably 1000 miles in the 25 before that. That will be a really beautiful car when you finish it I was stupid enough to pass on an R/T Hartop that color scheme same blue with White Vinyl top, white...
  19. 12icer

    What is it worth - 1969 Super Bee

    Looks to me like a weld bead around the torque box around the torsion bar not a good sign I would have to check the entire bottom for any repairs before even thinking about it just a small misalignment of any of the suspension parts can be a real headache
  20. 12icer

    1965 413 Rocker Shaft Question

    A heat gun is a Must for a thousand different things from heat shrink to dropping in a bearing by heating two or three spots around the outside just like two shrink welds to take out a stick race. As for the heads it depends on the application and the time it left the line I have Seen some...
Back
Top