Search results for query: *

Thank you for the answers. But the main issue is the left side one that is completely in closed by the K member. If I cut the head off it will fall inside and no access to it at all! Can I cut an access hole in the K member and weld the hole up?

Thank you, but I cannot get to the left one by the frame rail. It is all inclosed in the K member.

Hello everyone we need help!!! On our 66 Charger the bolts that hold the steering box on the K member have been over tightened at some point and the nuts that are welded to the K member have snapped the welds and just spin!! We got one bolt out on the right upper. The lower right one we can get...

Thank you!!

Thank you!!

My issue is not the steel brake line end for the hoses. It is where the hose screws into the wheel cylinder end for the front brakes. They just don’t seem to seat correctly. And yes they are both knock offs from Rock Auto! Can I get factory ones? Thank you for any advice!

Thank you! New question? We bought new front brake hoses and wheel cylinders. When I put the hoses on them it does not appear they seal correctly? Have you ever seen this issue?

I will try this for sure! As far as the plug wires I have read that number does not matter for the location and just do the firing order from where you need it to start from. It runs okay but the distributor needs to turn more to set it, but it hits the head now before I get the correct timing...

Thank you for the information!!

Thank you so much for the help!!!

Thank you for the reply! I think you are correct on moving the shaft. I think it needs moved so I can get the timing set correctly! I have raced Chevrolet engines most of my life and do not have much experience with Dodge or Chrysler engines or vehicles! Do I use a magnet to lift the shaft and...

The location of the vacuum advance is not the same as most pictures I have seen, ours is turned towards the radiator a lot more. And still needs to go more. To get 12.5 degrees at 500 rpm. Problem is the cap hits the head and won’t go more! That is why I think it maybe 180 out? Or maybe the plug...

A friend of mine came over and looked at our engine numbers. He advised we have a 1970 383 in our 1966 Charger we purchased. I have problems timing the engine. I have a Snap On timing light that you can dial to the desired degree. I set it at 12.5 degrees. With the vacuum advance hose removed...

A friend of mine came over and looked at our engine numbers. He advised we have a 1970 383 in our 1966 Charger we purchased. I have problems timing the engine. I have a Snap On timing light that you can dial to the desired degree. I set it at 12.5 degrees. With vacuum advance hose removed. It is...

Thank you so much for the great information it will help tremendously!!! My son loves this car but it has fought me every step so far! The previous owner did horrible repairs to this poor car! And took things apart with out saving the parts. The price of parts used or new are just crazy!!! But...

I can see what you are showing me, but it appears ours does not touch those ears for some reason, clicked in either direction? Like the ears for it to click against are way too short? Ours was all broken so I’m not sure what it should look like from the factory? I have one more question. At...

Thank you so much! I see the clip you show in the photo on our steering wheel. But mine appears to not touch the ears at all? With it turned right or left of the turn signal. The steering shaft just spins. Maybe the steering wheel is not going all the way down on the steering shaft? Someone had...

Thank you for any help and welcomes! I believe the 66 and maybe the 67 Chargers are setup differently than the 70s models? I would greatly appreciate a photo with just the steering wheel removed and the bottom of a steering wheel photo if possible. Thanks again for any help!

Hello everyone! I have been here for awhile now. But I could not get in from my old sign on! I tried everything! My son and I are restoring a 66 Charger for him. I just repainted and rebuilt the steering column. And replaced the turn signal switch. This car was partially torn down when we bought...