Search results for query: *

Hey guys had a pretty mph related vibration in my 73 bird. So I took the cheap route first and balanced my tires and driveshaft. Still had the vibration. Pulled the tranny to have it rebuilt, was leaking out of the front and rear seals anyways. Plus I had quite a bit of play in the yoke...

Cleaning out the back room of my shop today and found 8 in the box pistons with quite the dome. Punched the part number on Google and found something saying that it is a .060 over 11.5 to 1 400 piston can anyone give any insight to that? Part number p3690832

Just looking to see if anyone has a 440 forged crank kicking around that they aren't using, thanks!

Hey guys, last year I was running a power wire for my stereo down under the dash above my pedals, I noticed a pigtail connector that goes from the steering column to wiring harness. It actually prevented me from being able start my vehicle, so I bypassed it with a push button start (cheap way)...

Nothing professional by any standards, it was at the New England Summer Nationals at Thompson Speedway, They sectioned off a 300' straight line and brought a small staging light, Nothing special but it was extremely fun. With three people in my car I was able to run a Judge, a 67 camaro, an sn95...

Finally got the 3.91 suregrip back from the tranny shop! 2 months for a bench job...But whatever, he charged me less than he quoted me, I tossed them in the other day to replace my worn out 3.55s on my stock bottom end 400, with 915 heads. It pulls considerably more but the thing I enjoy most...

A guy actually came down to my shop this morning knowing that I have a mopar and asked if I was interested in a 440 out of a late model motor home, along with an automatic tranny I told him not particularly because I didnt think I would have the coin for it. It has 43,000 miles on it and he...

Hey guys, looking to raise the rear of my vehicle to clear my tires. I currently run 275's with air shocks, but would rub with out them. I am swapping over to SS springs but do not know if it will clear the tires even with the SS springs. I want to get rid of the air shocks, and don't want to...

Hey guys, its getting nicer up here in the northeast so I figured I would put some coin into my old bird. I am in the process of rebuilding a set of 3.91's to replace my 3.55's. I would also like to pick a different carb with the advice of you guys. My set up is a stock bottom end 73 400 with...

My gear shifter arm broke off on the threaded area tonight, anyone have experience replacing them, and is it a hard procedure? Thanks

Looking for possible culprits in my loss of oil pressure. Its a 400 big block that I run 20w 50 in. Until recently it always held around 60-65 psi cold and when warm it would drop to around 45 psi at idle. It would also go up around 10 psi per 1k rpm Seemed great. Recently at cold idle it stays...

I am seriously about to sell this car and buy a god damn chevy this thing is so irritating its not even funny, one thing after another... Went to adjust my shifting mechanism the other day and tighten it up, I noticed that my a833 shifted over about an inch to the drivers side. undid the tranny...

Ok, some people may think I'm an idiot for wanting to remove it, but I'd rather just take my shirt off and cruise with the windows down than leave the windows up with my ac on. I just got off the phone with Bouchillon the gentleman had some very interesting information for me and seemed very...

Headed up to the track for the first time Wednesday (lebanon or epping) not sure yet. Anyways just wondering what you guys think I might run, The set up is a 73 runner 4 speed with a stock bottom end 400, 284/484 cam, 3.55, mcleod clutch, Long tube hookers, Edelbrock dual plane intake, edelbrock...

I was rummaging through craigslist the other day I found a 383 with a steel crank...not sure if its a factory steel crank or an aftermarket but it also has what he said were pop up pistons, I'm assuming they're just domed instead of flat tops. He didn't give me any info on the pistons them...

Just looking for ideas to make my car go a little better its a matching numbers 400 4 speed with 3.55's in the back. It currently has the 284/484 cam with a set of 915 heads with 3 angle valve job. edelbrock intake, and edelbrock 1407 carb. I believe its a 750. It goes alright but it just doesnt...