• When you click on links to various merchants on this site and make a purchase, this can result in this site earning a commission. Affiliate programs and affiliations include, but are not limited to, the eBay Partner Network.

FOR SALE 1973 Plymouth Satellite parting out...

Status
Not open for further replies.
Hueyjockey said:
Look for the rear license plate assembly, does have one?
Thnx
Click to expand...


Yes I do have the rear license plate bracket but it's missing the spring. $10.00 + shipping.

20170905_204805.jpg


20170905_204756.jpg
 
'68 Charger said:
Hello FBBO members,

Parting out a 1973 Plymouth Satellite. This was a 318 auto with A/C, buckets, slap stick, rallye cluster, tan interior. No motor.

Sorry but I'm late posting this ad and some parts have been already sold, they are:

RH fender
LH fender
Trunk lid
RH door
Front windshield
Rear bumper/brackets/reinforcement bracket
Tail light lenses (housings still available)
Upper cowl
Bucket seats
A Pillar trim RH & LH(interior)
Rallye gauge cluster
Trans.
K frame

Prices on some of the key parts:
Grille PIECES for repairing other grilles $30.00
Grille upper trim, dents $50.00
Header paner trim, dents $50.00
Flat hood $50.00
Roof $350.00
Front disc brakes set-up 11" pin type (spindles/knuckles/rotors/calipers&bracket) $275.00
Upper A Arms $50.00 (pair)
Lower Control Arms $50.00 (pair)
Rear windshield (factory tint) $100.00
Rear windshield Trim (aluminum) $100.00 complete
Front windshield Trim (top aluminum, bottom and corners stainless) $100.00 complete
Side door glass tint $40.00 each
Quarter glass tint $40.00 each
Front bumper shell $125.00
Front bumper brackets $75.00 pair
Front bumper reinforcement bracket $50.00
Front bumper guards $100.00 pair
LH door $150.00
Header panel $100.00
Headlight bucket brackets/buckets/rings $60.00 pair
Front valance (thrashed) $40.00
Rear valance, 1 brace needs welded back on, surface area mint $175.00
Rear tail light housings $125.00
Front lower door panels (tan) no chalking $60.00 (pair)
Front upper door panel, tan with wood grain (RH) descent shape $30.00
Rear upper door panels, tan with wood grain fair shape $30.00 pair
A/C heater control very clean no cracks, no broken vac ports $75.00

Auto Slap Stick (linkage sold)
- Shifter (no T handle, no bezel) $75.00
- Console brackets (3) $75.00
- Console brackets attached to floor/hump cutout section $125.00
- Wood grain plate (needs new wood grain paper) $40.00
- Tan console shell (no door, broken, cracks) $30.00

Many more parts, please ask if available and for pricing. Pics available upon request.

Prices above do not include shipping cost. Parts are located in Las Vegas, NV. Local pick up is available. I can ship Greyhound for big parts.

Thanks

View attachment 440753 View attachment 440754 View attachment 440755 View attachment 440756 View attachment 440757 View attachment 440758 View attachment 440759 View attachment 440760 View attachment 440761 View attachment 440762
Click to expand...
Looking for heater box and possibly drive shaft
 
Looking for heater box and possibly drive shaft
 
jaygtx440 said:
Looking for heater box and possibly drive shaft
Click to expand...

Do you need heater only box? If so mine's an A/C heater box. If you do need the A/C heater box I have a current pending status on it and I will keep you updated of the transaction.

Drive shaft is from a SB car which would be longer if you were looking for a BB drive shaft. I can get measurements.

Thanks
 
'68 Charger said:
Do you need heater only box? If so mine's an A/C heater box. If you do need the A/C heater box I have a current pending status on it and I will keep you updated of the transaction.

Drive shaft is from a SB car which would be longer if you were looking for a BB drive shaft. I can get measurements.

Thanks
Click to expand...
Interested in heater box. Please send measurement of driveshaft. Thank You, Jay
 
jaygtx440 said:
Interested in heater box. Please send measurement of driveshaft. Thank You, Jay
Click to expand...


I have two drive shafts to chose from.

Driveshaft 1:
Ear to ear = 53"
U Joint center hole to yoke center hole = 51-1/2"
Tube diameter = 3"

Driveshaft 2:
Ear to ear = 57-1/2"
U Joint center hole to yoke center hole = 56"
Tube diameter = 3"
 
I think that shaft number one might work. Going out to check on mine now.
 
Oh well, my driveshaft measures the same. I actually got that from a '72 Charger with a 400, but it was in the trunk. I always figured it would work on my '73 roadrunner GTX with the 440. I need approximately two inches shorter.
 
jaygtx440 said:
Oh well, my driveshaft measures the same. I actually got that from a '72 Charger with a 400, but it was in the trunk. I always figured it would work on my '73 roadrunner GTX with the 440. I need approximately two inches shorter.
Click to expand...

Well it was worth a shot. Good luck on your search.
 
Garys8 said:
Do you have the steering column coupler that attaches to the power steering gearbox?
Click to expand...


Hello Gary, So sorry I never replied back to your question as I was revisiting this thread for updates. I know that it was almost two weeks ago but to answer your question, I only have a coupler from a standard steering box.
 
Do you still have the trunk lid? And the trunk rail/ gutter from side to side above the tail lights?

Inked1971-Roadrunner-trunk_LI.jpg
 
Status
Not open for further replies.

Similar threads

'68 Charger
  • Locked
FOR SALE 1968 Plymouth Satellite 4 door parting out.....
2 3
Replies
49
Views
8K
vabchmopar
V
S
  • Locked
SOLD Parting 1973 Dodge Charger ( WH23 Car)
2
Replies
20
Views
3K
Mike meeks
Mike meeks
C
  • Locked
FOR SALE Carlisle 2023 Parts Spaces IA1 IA2
Replies
0
Views
736
cudaize
C
Liberty MW
  • Locked
SOLD 1974 plymouth satellite parts
Replies
4
Views
1K
Liberty MW
Liberty MW
C
  • Locked
SOLD Parting out, or whole as-is: 1969 Dodge Coronet 440 Deluxe Wagon - 318/904
2
Replies
32
Views
4K
derush
D
Auto Transport Service
Back
Top