• When you click on links to various merchants on this site and make a purchase, this can result in this site earning a commission. Affiliate programs and affiliations include, but are not limited to, the eBay Partner Network.

Recent content by cruizer88

  1. 1964 Dodge Polara "done"

    1964 Dodge Polara "done"

    I finally have this car done to 97%. I say this since they are never really "done". It started life as a 318 car and now has a 1964 426 wedge (+0.060") Lots of performance parts. All good stuff. Looking to race it this spring. Hoping for 12 's. I'll post once the front end hits the timing lights.
  2. cruizer88

    1964 Fury non AC heater control valve. HELP!!

    I rebuilt my own heater control. Took out all the old plastic pins and replaced them with copper tubing. They are press fit and I added a little JB weld insurance. Not all that hard. Be careful not to drill to deep as there is a "slider" under the holes that direct the vacuum. when you push the...
  3. cruizer88

    Factory steel wheel .

    so, for sale?
  4. cruizer88

    1964 Dodge Polara seat belt upgrade

    thanks. I'll check it out.
  5. cruizer88

    1964 Dodge Polara seat belt upgrade

    Yes, factory seat. Thanks for the info. I'll keep looking.
  6. cruizer88

    1964 Dodge Polara seat belt upgrade

    Anyone out there have any information about upgrading seat belts in a 64 Polara? Specifically a shoulder harness without a roll bar. Thanks, Bill
  7. cruizer88

    Comment by 'cruizer88' in item '1964 Dodge Polara - running and on the road...finally'

    Beautiful car.
  8. cruizer88

    Comment by 'cruizer88' in item '1965 Plymouth Belvedere'

    It has good bones and will be fantastic once restored.
  9. cruizer88

    Comment by 'cruizer88' in item 'My son's 74 Charger Restoration'

    That is a ton of work. Great project. Cool car. It'll be sweet when done.
  10. 1964 Dodge Polara - running and on the road...finally

    1964 Dodge Polara - running and on the road...finally

    Well, my 64 Polara 426W (+0.060) is on the street. Not legally yet, but on it anyway. Its not perfect, but I'm not out to impress anyone but me. I built this car from a rough start and have all the photos to prove it. It is resurrected. Most everything works too. The engine runs great with no...
  11. cruizer88

    Comment by 'cruizer88' in item '64 Polara progress update 3/23/21'

    The trans linkages is in and adjusted. I welded in a section 2 1/2" long to the downshift rod (at the bottom). This keeps the rod in the proper position for a streight push-back. A friend of mine added 2" to his 63 down shift rod on the top section and that never worked right. So I learned form...
  12. cruizer88

    What did you do to your Mopar today?

  13. cruizer88

    What did you do to your Mopar today?

    I hooked up my push button shift linkage on my 64 Polara. Now I got to go out and put the trans pan back on. Then I have to extend my downshift rod by ~2" and get that set correctly.
  14. cruizer88

    Comment by 'cruizer88' in item '64 Polara progress update 3/23/21'

    All my glass went in OK. The rear was way easier than the front. Lots of soapy water. Love the Roadrunner. My pal in high school had one wand we did a lot of street racing.
  15. cruizer88

    Comment by 'cruizer88' in item '64 Polara progress update 3/23/21'

    I do have a spacer under the carburetor. Intake is a Mopar Performance Wedge intake.
See more
Back
Top