• When you click on links to various merchants on this site and make a purchase, this can result in this site earning a commission. Affiliate programs and affiliations include, but are not limited to, the eBay Partner Network.

`70 road runner, FC7, 383, 727 It`s waited long enough, finally time to get it done.

Not much progress lately as I've been busy with wife, kids, house etc. but even when I have had some free time lack of motivation has kicked in. I think it is a combination of a long, cold, snowy winter and being in the seemingly never ending bodywork stage that has me a bit beat up both physically and mentally. I guess I needed a short break from it as any of you who have done a major project understand. So since it's finally spring it's time to get my Barracuda ready for the season. I just replaced the battery and other than an oil change at some point it's ready. I do have an AAR hood I want to put on that I bought a while back so decided to get it ready, it's pretty good quality but of course it needs a bit of ...... bodywork! :rolleyes:

20260415_110452.jpg
 
AAR hood is ready for test fitting and then primer but I'll need some help to do that so back on the road runner. I got the drivers door and fender gaps good so I can fine tune the fender edge and start the filler work. Passenger door is on and quarter gap is good but I need to get the reinforcement welded in the fender before I test fit it.

20260430_143122.jpg


20260430_143140.jpg


20260430_143200.jpg
 
One step forward four steps backwards. I got the passenger door and fender aligned pretty well. I got the air grabber hood out of the shed to test fit it to the fenders and when I was rinsing the dust off it I noticed a patch of filler hiding under the paint. The hood is not original to the car as it didn't come with the option but I bought it years ago shortly after buying the car. Grinding it down I found a bunch of rust thru mostly on the rear passenger side but also some along the middle and a couple small spots on the drivers side. It's bad enough that I will have to split it from the outer skin to repair it properly. Yay- more hours cutting, fabbing, welding and grinding.

20260508_111844.jpg


20260508_161520.jpg


20260508_161525.jpg


20260508_161530.jpg


20260508_161534.jpg
 
Found a hood local and cheap! I had already searched Marketplace with no luck but decided to change what words I was using and a Satellite hood showed up 20 minutes away. It has a bunch of surface rust but nothing thru or soft so should clean up fine. It is a bit different than the road runner air grabber structure so while I would rather have used one complete I think the easiest way is to just cut out the rear sections I need. It came with a '71-74 Barracuda hood thats solid and I of course asked if he had any other Mopar stuff and got a box of '72-74 'cuda tail lights, some new rubber weatherstrips and miscellaneous stuff. Both hoods were $100 and I offered $40 for the box of parts so great deal! I now have a couple hoods to cut apart.

20260514_100313.jpg


20260514_094048.jpg
 
Air grabber is split. There are a number of differences in the two as far holes and cutouts but I'll make it look factory.

20260522_155733.jpg


20260522_155750.jpg
 
One of the ways how I am restoring this car for well under $40k - stripping parts by hand and sand blasting what is needed myself. Yes, it would be quicker and easier to have it done but probably cost $100 or more plus gas and time getting it there and back and multiply that by how many individual parts to be done. Sure it does cost some money in electricity and supplies but the savings do add up. It does suck how long it takes though.

20260613_113518.jpg
 
You must log in or register to reply here.

Similar threads

torredcuda
A couple big decisions on my road runner restoration - help me decide.
2 3 4
Replies
61
Views
6K
dodge1972
dodge1972
road robert
Time for New vs. Rebuilding Carburetor for '71 road runner 383 4 Speed - Is My Carter AVS 4966S The Best Choice?
Replies
9
Views
1K
RJRENTON
RJRENTON
beebest
70 Road Runner next project
2
Replies
20
Views
4K
biomedtechguy
biomedtechguy
EWJ
  • Locked
SOLD 1968 Plymouth Road Runner: 383/4 speed/3:55 Axle Package car
Replies
3
Views
4K
EWJ
EWJ
moparedtn
So....I took Fred to get new tires put on today - Ed story time!
2 3
Replies
56
Views
7K
Curiousyellow71
Curiousyellow71
Back
Top