Search results for query: *

where can I get a quart of 3M brushable seam sealer. It says it can't be sold in Massachusetts??

Looking for a drivers side aluminum wide panel that is attached to the door panel under the armrest. If it matters this is a non a/c car. Please send me a picture as I am looking for straight/clean parts. I would also entertain buying a pair for both doors if need be. This is for a 1966...

HI, My 416 stroker kind of loads up a bit and when stopped at idle, with the windows open it kind of smells raw fuel. As soon as I drive away, the smell subsides. I had this 340 dyno tuned by 2 places which told me that was the best they could get the fuel to air ratio and it would run a...

This is a brand new panel made from Marine Grade plywood to prevent the delamination we see on these. It comes complete with all new teenut inserts, and refurbished hinge as well as refurbished catches. The stainless trim has been buffed to a high sheen. All that is needed is to install the...

This is a reproduction trunk divider panel I make. It is made from 1/2" Marine plywood so it will last. This one has the chrome trim and also the hinge and the 2 catch bolts. It has all brand new captured threaded inserts and fits exactly perfect. It is painted 2 coats of a nice satin black...

HI, Since I cannot find a decent used inner trunk cover for my tail lights and it appears there is no repops to be had, I am thinking of reproducing these myself. But what I need is a few nice clear photos of what they look like. If anybody on here has a correct one installed in their 66, I...

OK folks who have been following this thread. I have been trying hard to solve this issue. I checked and replaced my starter with a new mini starter. I replaced my starter solenoid switch. I checked all the connections and made sure they were all clean and tight. It was then mentioned on here to...

What would cause my front light wiring to melt in a matter of seconds? Right down to bare wires for about 2 feet from the headlight and also the side marker light? Key was in the on position. Car would not start in the start position only making a buz at the starter relay. I removed the...

Looking for an original or a repop taillight inside trunk finish cover.

Looking for the switch for my 66 that keeps the rotating headlights open or closed. Has a chrome toggle in the left side of the dash? Anyone got an extra they want to sell?

Looking for the 66 charger rotating headlight hold open switch that sits in the dash. Has a chrome toggle that switches up] and down. Anybody got one they would like to sell?

Doing a resto on the steering column and I lost the screw that holds the directional arm to the new turn signal switch I installed. I was wondering if anyone on here knew what type and size? Also, is there somebody who just sells the spring that goes inside the column joint to hold those two...

Looking to replace my 66steering column harness with a non cut original? Pictures please.

I bought a ready to run for my 383 and was curious about hooking it to the 6AL MSD ignition box and what the advantages of doing this? MSD says the RTR distributor needs no ignition box but they also show a diagram and say the RTR can be used with the ignition box? But they do not clarify why...

Looking for a pair of 66 charger heater control knobs for a non a/c car. Need to be clean. Thanks

Hi, getting to my dash now. I have no radio in it. Is there a radio I can install with the bluetooth and serius to work with the EL lighting or maybe look like the EL lighting. I don't want to look for a stock radio as I prefer bluetooth and hands free phone. What has everyone here done for...

1970 Dual snorkel air cleaner. Has been blasted, primed and recoated with the wrinkle finish as shown. Comes with the brand new repro 383 magnum pie plate in hemi orange color. $550 plus he ride.

These are the clips that hold the 66 hood moulding as well as the lower grille moulding. We did them in stainless steel. I have a few sets left. They are $170.00 and shipping to you is FREE. While supplies last......

does anyone know what the correct bulb I should be using in my 66 Charger front console. Has a lamp on both sides and it is missing the bulbs. Auto parts store sold me 1156 bulbs but they are like 32 watts and seem to be for something much bigger. I don't want to burn the plastic lens with...