Search results for query: *

Hey guys, my edelbrock 1403 has a secondary lockout. As far as I googled it, this should avoid opening of the mechanical secondaries if the choke is closed. But the secondary lockout lever is dangling around freely. It can even prevent the secondaries from opening, if the choke is fully open...

Does someone know why there are 2 values (difference always 0.01") for each dimension? Which one is correct?

Hey guys, I disasembled my 8 3/4" (741) rear axle and noticed that I must have obertightened the U bolts. They dug into the axle about 1/8". Can it be that the axle is distorted now? I diasassembled it because at first drive after resto, the rear end was extremely loud and leaking. I think it...

I got 3 point belts for my 68 coronet from seatbelt solutions. I noticed by looking at the design of the buckles (pictures) that they are not form fitting. The anchor is just held by a spring loaded ramp. Under tension, this ramp is pushed up and the buckle opens. I tried it. I contacted my...

Just tried to install the windshield, but we couldnt get it into the gasket. No chance. Could it be that the gasket is too thick? I have the one from Dantesparts. It looked like it was of good quality. But i really cant imagine how to get the windshield into it. Is there another source of...

Howdy, does anyone have a dimensioned drawing of the crankshaft (to flexplate) bolt pattern of a 360 LA small block? Do stroker crankshafts usually have the original bolt pattern? Thanks a lot... Dieter

Hi Folks, whats the difference between the park lamp (wire L6-18BK/Y*) and the side marker lamp (wire L17-18DGN*) in terms of activation? Shouldnt both be activated at the first position of the head lamp switch and therefore more or less be the same? My car is a 68 Coronet 4 door sedan and i...

Hey Folks, could anyone give me the measurements of the brackets which are bolted to the rear subframe? Its a pretty simple part. As the thread title says, I'm talking about the Hotchkis rear sway bar brackets. Background is, i want to weld them to the subframe instead of bolting them, because...

...in good condition, expecially around the tail lights, wanted!

Hey Folks, I'm restoring my 68 440 318cui 4 door Coronet with A/C (at least it had one) and currently working on the heater case. In the manual i saw that there should be a tube attached at the engine side of the blower motor. Once its called "motor cooler tube" and later its called "air tube"...

Hi Folks, is there any company where i can order custom flexplates or a blank 3rd gen hemi to NAG1 flexplate with only the middle hole already stamped so that i can drill the others by myself? Many thanks Dieter

Hey Folks, let me tell you my story. I bought a 360LA which ran in a offroad jeep until then. The guy said it is internally balanced, but google says every 360LA is externally balanced. The harmonic dampener at the front is for a internally balanced engine. The flexplate that came with it is...

Hi BBody guys, straight to the point. My '68 TF 904 makes horrible noises. But first what i did: The transmission was leaking everywhere. I had it out to install new seals for the shifter lever. So I straightened and cleaned the pan, gave it a new gasket and replaced the outputshaft seal. I...

hi guys, does anybody have a complete wiring diagram for my '68 318 A904 dodge coronet 440 4 door or knows where i can get it? The search function didn't bring usable hints... Tanks and greets from austria!

Im Dieter from Austria (the Schwarzeneer Austria, not the kangaroo one) and i have a '68 Dodge Coronet 440 4 door. Its a 318 with the 904 and the 8-3/4" rear axle. I have some plans for it, but for now i have it to get registered in austria.