Follow along with the video below to see how to install our site as a web app on your home screen.
Note: This feature may not be available in some browsers.
When you click on links to various merchants on this site and make a purchase, this can result in this site earning a commission. Affiliate programs and affiliations include, but are not limited to, the eBay Partner Network.
Hello
So for minor floor pan rust, is there any real rust incapsulating paint or is it all just snake oil ?
Been sand blasting anything that I can get too, but there are those spots that it would be awesome to have a magic spray on “ bullet”
Thanks
As of now
I took the original console and overplayed a piece of kydex formed with a heat gun.
Better than a hole but not perfect.
If/when I get a new console it will be reinforced,
Possibly a couple of 2x4s glued together than sanded down to correct length/contour and glued to base.
Or
Some sort...
Hello
Anyone have any reports on the aftermarket 4spd center consoles for 69 Charger 4 spds and the quality or lack of ?
My biggest concern is the very back end that everyone puts their hands and weight on, getting in and out of the back seat, and it gets crushed/cracked like the originals.
I...
Hello
Refresh my old mind.
Did Dodge make a "RT" or were they Coronet Rt's that just had an RT badge on them and no Coronet name plates ?
I had thought they did, but it has been a while since I have looked into these.
Any history on this subject would be appreciated.
I normally am a Charger guy...
As caliper piston pushes in, the caliper itself moves toward the piston, thus sliding on the brackets, and if not on the bracket, I too see it hitting and hanging up, causing issues.
IF, it had at least an 1/8" resting on it, I would consider using it, but even then would not feel warm and fuzzy...
Yeah
+1 on Dr Diff
Wish I had dealt with them more in the past,
No issues with items I have gotten from them and all ?s replayed too.
The spindles and brackets were bought as a kit from competitor on sale.
Live and learn
Hello
I am installing 11.75 rotors on my 66 Charger using the slider type calipers.
I could not find any junk yard donors for the brackets so I bought a new manufactured set.
Installing my calipers the right side barley rested on the slide, but with future pad wear, it will get better.
The...
So my Mechanical fuel pump is leaking
This is a 110 gph street strip pump, with a slotted screw on the bottom “bowl” to adjust and point the inlet to where you want it.
I can’t remember if it is a Holley or a Carter, but it has the screws around the casting to take it apart and rebuild
Picture...
Lower control arm bushings.
The non threaded end of the shaft in picture, get pressed into these,.
It will look like a WWII German granade.
Potatoes masher.
Then it gets pressed into lower control arm.
Look at the QA1 add to the right of your post on screen.
Good luck
Can anyone give a good reason for me to keep the old drum spindles and the drums them selves, from 66 and 69 chargers ?
Swapped over to front disks with the E body spindles,and I can not think there is a need for drum spindles out there ?
Maybe keep one set of drums from future replacement of...
Hello
What are the Timken inner and outer bearing numbers for the 11.75" rotors used on the drum to disk swap ?
A17 the inner/bigger bearing ?
Then the smaller/outer bearing is A16?
Found a old receipt that had these along with brake pads sooooo ?
Thanks in advance
Hello
66 charger had power brakes, putting in manual with discs up front.
I have a 69 charger with manual brakes that I upgraded to discs with same componnets.
Please see attached picture.
I assume the linkage the pencil points too gets tossed into the spare parts bucket, then my new adjustable...
So,
I am rebuilding a 66 charger and going to add front disc brakes.
I am going to have to move and would like to finish the front disc brakes and block off/ cap the rear brake line after the proportioning valve, and use the fronts only for getting it on and off a trailer and into storage.
Is...
Just an update
The Evil Empire had bolts of burlap and felt, and they also had the spray can adhesive.
The did not have any foam.
So, since the other stores are closed for the zombie virus , I went on e bay and got some half inch foam coming.
Wire, plan on using wire from work, ceiling wire, the...
Hello
69 Charger
Finally bit the bullet and ordered the Legendary foam and vinyl for my front seats.
The sent the cloth material you glue onto the foam, but they say I need felt and 1/2" foam for the installation.
My bad for not looking into this further. I assumed that the foam kit would have...