Search results for query: *

I am removing the 4 speed in a 67 GTX. Got everything disconnected, but just wanted clarification on where to support the engine while the trans is out. I currently have a block of wood under the oil pan, on the sump (deeper part of it), right by where the drain plug is. Is this the best place...

Hello All, I asked about garage building in a prior thread (Garage Planning Questions) and everyone was very helpful! I was hoping to get people's thoughts on the following: I am allowed 1000 square feet, and 16 feet tall at the tallest point. I would like to be able to fit 4 cars and have a...

Hey Everyone, I'm looking for some pole building garage companies that work in/near the NJ area. I'm sure that extends into PA and NY. So far I've seen Fetterville and Pioneer Pole Buildings. Anyone have any experience with them/know of any others? Thanks in advance!

Hopefully shortly I will be replacing my leaf springs, and while doing so, I wanted to detail the parts as much as possible. I know some components were left bare, and not sure if it varied by the factory that the car was built. Car is a 67 GTX/440/4-speed. But does anyone know the stock colors...

To give a little background, I rebuilt the front suspension on my 67 gtx a few years ago. Before the rebuild, the car tracked straight and the steering wheel was centered when doing so. During the rebuild, I found that the ear on the lower control arm (I think pass. side) where it attached to...

Does anyone on here have New Jersey QQ plates? How hard was the process to get them? Also, does anyone have vintage NJ plates from the 60s? Is there a process to get them for your car? New Jersey License Plate History Article That article makes it seem like no, but I was wondering. I always...

I am in need of some explaining on distributor mechanical and vacuum advance springs. On the mechanical springs: Do the springs limit the actual amount of mechanical advance, or when the advance comes in/how fast or slow it does? On the vacuum advance (VA) springs: Does the spring limit the...

Hello all, I re-installed the original cast iron dual point distributor on my 67 GTX. It is a 440 4-speed car. When going through the FSM specifications, it does not give any specs for a dual point. The tag on the distributor says: CHRYSLER 2642911 IBS-4006-Y 67 Does anyone have any info on...

Do you guys know of any companies that sell new drum brake pads and/or drums? Looking for 11x3 & 11x2.5.

Hello All, I am starting to plan out and get quotes on having my garage built. I am allowed a 1000 sq ft footprint with the highest point being 16' without a variance. My goal is to fit 4 cars, side by side. My initial thought was to build a 40'W x 25'L garage, with 2 16' doors, and going as...

Hello All, I've read through the numerous threads on here about 4 post vs 2 post lifts, and from them I have gotten some ideas. I understand the pluses and minuses for both types of lifts. But one question I couldn't find the answer to was as follows: How good does a 4 post lift work for...

For sale is a 66-67 Plymouth Belvedere/GTX 150MPH Full Cluster Kit from Premium Dash Decal I bought for my own use but went another route The decals are un-used and have always been inside Make offers Starting at $50 Free shipping

Hello All, Does anyone know if anyone make hangers shown below that look stock, but are a bit longer. I know I've seen ones with multiple holes, but I am looking for a stock look. It seems like all reproduction ones at 5" long, but I have a set on my car that are 5.5" long. Looking for one's...

Hello All, I am having rear tire fitment issues on a 67 GTX (no surprise there). Currently on the car are rims with a 4 1/8 backspacing, and 235 70R15 tires. The old leaf springs were shot and air shocks were used to raise the rear. The leaf springs were just replaced with new ones that gave a...

In my 67 GTX with a 440/4 speed, I was driving yesterday in fourth gear. I had to slow down quickly (not overly hard) while going about 40 mph to about 15-20 mph. Upon doing so, my oil light in my dash cluster came on, and stayed on for a few seconds while I started accelerating again. When I...

Hello All, My 1963 Chrysler 4 door New Yorker has met its end. At this point I am keeping the front bench seat and the 413 motor. But the rest of the car is available, including the push-button 727 trans. The car was in an accident so the passenger fender is destroyed, and the passenger wheel...

I know I've seen companies produce reproduction exhaust manifolds for GM products. They've even gone so far to reproduce exhaust manifolds that have bigger ports as well. Does anyone know of a company that does this for Mopars?

Can anyone post any pics of real drag racing memorabilia from the 60s/early 70s? Searching online provided me with a lot of reproduction stuff that wasn't around back then. I'm looking for things like stickers, hats, shirts that you could've bought about mopars in general, or sox & martin, the...

Can you guys post pics of your power steering hose routing? That was the only way I could route the high pressure hose. And does the return line hose look too tight to you guys? There is some slack in it, but I'm worried that when the engine moves it'll strain the small pipe on the pump itself...

Hello all, Just installed a stock power steering setup on a 67 gtx with a 440. The power steering pump belt hits the spout on the water pump pulley. My crank pulley measures 7.5”. The correct one measures 6.5” part 1826053 I believe. It was used up to 68. Does anyone have one or two of this...