• When you click on links to various merchants on this site and make a purchase, this can result in this site earning a commission. Affiliate programs and affiliations include, but are not limited to, the eBay Partner Network.

Search results for query: *

  1. MT_Mopar

    "H" Drive Train VIN Difference - 69RR?

    If the VIN indicates an H drivetrain on a 69 RR, is there a difference compared to a non H? Are all 69 RR's H drivetrains? Thanks
  2. MT_Mopar

    Saginaw Power Steering Pulley Alignment

    I need my pulley on my new power steering pump to move out a half inch or so to clear my water pump pulley. The existing pulley is dished, maybe I could flip it? Shim it out some? Currently it lines up with my crank inside pulley, if I go that route I will need to find a water pump pulley...
  3. MT_Mopar

    Skid Plate Options?

    I have a 7+ Qt oil pan, It hangs down pretty low. I am worried about hitting something and draining out my oil. (BAD!) I have been checking out skid plates, is there a problem extending the existing skid plate to cover part of the pan? My cardboard prototype below. (has access cutout for...
  4. MT_Mopar

    New Torque Converter Took a Crap

    New Tranny - Torque Converter Took a Crap Well crap – Started up the Coronet for a car show, let it warm up a bit and pulled out. When I put the car into reverse there seemed like there was nothing there, I goosed the pedal a little and made it out of the shop. When I got the car out of the...
  5. MT_Mopar

    Power Steering Pulley Swap

    I need to put the pulley on the left on the pump on the right. It appears the pulley on the left is pressed on and the shaft is larger than the one on the right, also the shaft on the right is tapped for threads. Do I need to find a different pulley that will work for the pump on the right...
  6. MT_Mopar

    Rear Axle Green Bearing Install Questions

    I have a new set of Moser Engineering rear Axle Bearings 9400M coming on the UPS truck. I've had a small leak on one side of my 8 3/4 rear axle for a while, so I decided to switch them both out with the green snap-ring style. I have a new Eaton Tru-Trac that I installed with the thrust block...
  7. MT_Mopar

    Shorten Water Pump Shaft

    I need about 3/8" more clearance for my electric fan housing to clear, would it be a big deal if I cut the stub end off my Milodon water pump shaft? If I do that, and replace the bolts sticking out with counter sunk heads that will give me enough room to clear my electric fan housing. I can...
  8. MT_Mopar

    TF 727 Temperature Sender Install?

    I have a new TCI TF 727 SSF I also have a new trans temp gauge from NVU: http://www.summitracing.com/parts/nvu-40195-01 What is the best place to install the sender into the transmission? Says it is a 1/8th NPT, maybe a bushing needed? Thanks
  9. MT_Mopar

    IQ52's BigBlock Lineup

    Jim and Cody Laroy have been building some awesome bigblocks this spring and summer, including mine. He sent me this picture, I thought everyone would appreciate. I can't thank Jim enough for everything he has done on my motor including answering all my dumb questions like: "Is it...
  10. MT_Mopar

    Turbo Action Cheetah Shifter Cable Help

    I am installing a Turbo Action Cheetah shifter in my car - New motor, New TF 727 trans, New shifter. I was looking for guidance on the shifter cable routing before I make a hole in my trans hump. From the pictures below, would it be best to coil the cable on the passenger side like shown...
  11. MT_Mopar

    67 Coronet Motor Install W/Headers Bolted Up?

    I am having my motor re-built starting next week, from all stock to a moderately built 440 with new hooker full length super comp headers, 2" primaries, 3 1/2" collectors. I pulled the motor with tranny installed no problems at all. Dumb Question: Can I reinstall from the top down, the...
  12. MT_Mopar

    67 Coronet and Hooker Super Competition Headers?

    I am having a 440 motor built for my 67 Coronet and have been checking out headers. My car has power steering, with an automatic transmission and my biggest concern is will the headers fit without a major PITA getting them installed. The ones I am looking to purchase are Hooker Super...
  13. MT_Mopar

    Differential Options

    I am in the pre-plan stages of installing a moderately built 440 motor in my 67 Coronet. Maybe a trip or two per year to the race track, but mostly a weekend warrior, impress the neighbors setup. I am checking my rear differential options, below are the stamps on my existing diff...
  14. MT_Mopar

    Aeromotive Phantom Fuel System

    Anyone using one of these systems in their car? I'm looking at fuel delivery options for a built 440. Solves the external electric fuel pump and trunk fuel cell dilemma with the same delivery. I was looking at a MagnaFuel system for near double the price...
  15. MT_Mopar

    Lokar Throttle and Kickdown for a 67 Coronet 440?

    I have a 67 Coronet 500 with a 1975 440ci motor, carb is an edelbrock 1406, tranny is a 727 auto. I am looking to switch out my old throttle cable and mechanical kickdown lever. Anyone running this setup with Lokar cables? Any part numbers and bracket part numbers/pics would help me a ton...
  16. MT_Mopar

    Hedman Elite Hedders - 67 Coronet 500?

    67 Coronet 500 with Hedman Elite Hedders 78038 - http://www.summitracing.com/parts/hed-78038 I have a nasty exhaust leak on my right side on a 1975 OEM style 440; I have been contemplating headers and a new exhaust anyway and was looking for some feedback on the Hedman Elite Hedders...
  17. MT_Mopar

    TF727 Shift Pin Seal Leak

    My poor old tired TF727 tranny is leaking, it appears to be coming from the shift pin seal where it goes into the case, is there a way I can reseal this without having to pull the tranny? Thanks for any suggestions. John
  18. MT_Mopar

    Dwell Degrees for a 1975 440

    Hi, I have the motor here: 1975 440 Stamping What should the dwell be set at during idle with a Edelbrock 1406 600cfm carb? Point gap is 0.017" correct? Thanks! John - Montana
  19. MT_Mopar

    440ci Block Stamping Info

    Hi, I am working on my 67 Coronet, it has a 440ci motor, there are some casting numbers and stamps on the block, I took some pics, other than the 440 stamp I was wondering what the other numbers mean, at the top passenger side there is stamping: 5 * 23 * 75, is that the month/day/year of the...
Back
Top