• When you click on links to various merchants on this site and make a purchase, this can result in this site earning a commission. Affiliate programs and affiliations include, but are not limited to, the eBay Partner Network.

Search results for query: *

  1. D

    Fuel Filler Hoses

    Happy Spring, Has anyone used rubber fuel filler hoses sold on EBay sold by US Stock? Thanks
  2. D

    Thrust plate

    Hi all, I have a 1967 383 and a TCI torque converter. I have a flex plate that fits the converter but the bolt holes are oval shape. Has anyone seen flex plates with oval holes? I also purchased ARP flex plate bolts but they have small bolt heads but mopar bolts have large heads. Thanks
  3. D

    Big Block Water Pump Housing Bolts

    Hi everyone, Can someone tell me which water pump housing bolts need to have permeated on them to prevent coolant from leaking on a 67 383 Thanks
  4. D

    Valley pan seal

    What do you use for the front and rear seal on a big block valley pan? Cork gaskets or RTV? Thanks
  5. D

    Thrust block

    Hi All, I'm going to replace the open diff on me 66 Coronet with a 3.23 sure grip. The 3.23 is missing the thrust block and I want to use the one from the old diff. How do I remove it and install it in the 3.23? Thanks
  6. D

    Flex plate

    I'm attaching the flex plate to torque converter bolts. Do they require washers? Thanks
  7. D

    U Joints

    Hi all, I changed out my rear end on my 66 Coronet. The yoke takes a larger u joint than what is on the drive shaft. Do they make a u joint with two different sizes or do I have to change the yoke? Thanks
  8. D

    Powder Coating

    Hi, I have an Edlebrock aluminum high rise intake. I soda blasted it and it looks good but I wonder if it came from the factory painted. I want to powder coat it and want to make sure that it's not painted. The soda blasting should have removed any paint. Thanks
  9. D

    Torque converter bolts

    Happy New Year Mopar Enthusiasts, Can anyone tell me what bolts to use to connect the torque converter to the flex plate on a 1967 big block and 727 tranny? Thanks
  10. D

    Valley pan gaskets

    Hi Mopar Folks, Do you recommend additional gaskets for the valley pan and intake or just the pan only? Thanks
  11. D

    Rocker arm shafts

    Hi all, Has anyone had any experience with Elgin Industries rocker arm shafts? I'm looking for some for a 383. Thanks
  12. D

    Water pump housing bolts

    Hi all, Installing the water pump housing on a 67 838. Which bolts need to be sealed with permatex? Thanks
  13. D

    Differential Lube

    Hi all, Looking for recommendations on differential lube in an 8 3/4, 3.23 posi unit. Thanks
  14. D

    Header Coatings

    Hi Mopar Folks, Has anyone had any luck with spray on header coatings? Looking for recommendations. Thanks
  15. D

    Washers on head bolts

    Hi, I'm putting the heads on a 383. I have Mopar head bolts and they didn't come with washers. Are washers needed? Thanks
  16. D

    Brake Lines

    Hi All, I'm converting to front disk brakes on my 66 Coronet. Does anyone know where I can find measurements for forming the brake lines? I want to fabricate them myself and it would be allot easier if I have the dimensions for bending them. Thanks, Dan
  17. D

    Leaf Springs

    Hi All, I'm looking at a new set of Mopar B Body rear extra heavy duty leaf springs, P4452982, same spec's. as the 440 & hemi option. I want to put them on my 66 Coronet. Will these springs raise the car allot? I don't mind a little but I want to keep it as lever=l as possible. Should I look...
  18. D

    Seam sealer recommendation

    Hi All, What is the best seam sealer to use on the interior floor pans? Thanks
  19. D

    Piston Question

    Hi Mopar Experts, I have a 1967 383 that I'm rebuilding. It originally had 516 heads and I'm going to put on 452 heads. It's bored 30 over and I'm using flat top pistons. My question is, are all flat top pistons the same or are there taller ones for open chamber heads. Thanks
  20. D

    Engine Swap

    I have a 66 Coronet, formerly a 318 Poly. I'm putting in a 383 and I would like to know if I have to do anything to the torsion bars due to the added weight. Thanks
Back
Top