Follow along with the video below to see how to install our site as a web app on your home screen.
Note: This feature may not be available in some browsers.
When you click on links to various merchants on this site and make a purchase, this can result in this site earning a commission. Affiliate programs and affiliations include, but are not limited to, the eBay Partner Network.
Hello everyone working on a 73 318 mild cam fresh rebuild ,after first start up got motor running,broke in cam but can’t set the timing can’t find the Mark when engine is running.Damper is good if I turn it over by hand line up Mark ,number 1 is at top dead center,I have distribtor pointed to 1...
Happy Hoildays getting ready to fire up a73 318 ;rebuilt by previous owner I was priming the motor today,I have a bad oil leak at filter housing ;I put that together I have a gasket for outside edge the double sided nut that screws into block to hold filter plate The other side the filter screws...
My cars a 73 Barracuda,can’t log on to the e body site ,anyway anyone have a picture of the spring install on the floor shift linkage it’s the fwd where the rod goes down through the floor ,my book is a 70 can’t find a picture thanks
working on 73 Barracuda tranny already rebuilt its a 318 mild cam ,Parts Geek list a converter but says 727 after it ? Does the 904 use the same converter ?? Its just a cruise night car thanks Gregg
Happy New year first off ,putting together a 69: Roadrunner 4spd 440 car it was an auto switched it over to a 4SPD ;engine is a a used 69 440 steel crank good heads ;my question finding 1 cyl on cap ;myself I normally get engine on compression stroke turn over until it lines up with 0 on the...
Hello all ,working on a new project 69 Roadrunner,swapping it over to a 4spd ,thought all was going well but ,I’m using a bellhousing 2892626,bought a used 833 had two mounting places for shifter so I think it’s a 70 or newer ,couldn’t find a date. On it the front bearing carrier is to big in...
Looking for a picture of 4spd shifter linkage 69 Roadrunner swapping my car over to a 4spd bought used 833 with used shifter bought dog ears from brewer think the 967 is reverse 891 2/1 and 068 4/3 ,I saw a picture some just can’t seem to find it again thanks Gregg
Hello I put together a 70 Roadrunner with a 440 auto Tranny,having trouble getting it to shift right ,car shifts to fast ,I tried adjusting rods to the longest position ,still no difference,springs are from hardware store ,any ideas were to start ?Car was a basket case off this fourm but I was...
Hello all ,putting drivetrain in a 70 Roadrunner anyway I have the big block drive shaft it has the large u joint both ends looking for a combo joint my center section probably from a a body has the small yoke it’s a 42 case ,anyone know what u joint I need thought it was 347 that’s not wide...
Hello all ,putting drivetrain in a 70 Roadrunner anyway I have the big block drive shaft it has the large u joint both ends looking for a combo joint my center section probably from a a body has the small yoke it’s a 42 case ,anyone know what u joint I need thought it was 347 that’s not wide...
Putting together a 70 Roadrunner Gona try setting up motor and auto tranny on the K frame and put it in from the bottom ,any pictures of how that up shift linkage gets installed never had an automatic before ,car was gutted shell when I bought found pictures of shifter install,confused on that...
hello ,putting together a 68 roadrunner,bought a used 65 383 out of a 70 roadrunner ,anyway need a damper bolt ,thought it was 3/4 inch fine bolt that only went in one thread ,so went to local hardware picked up 3/4 corse thread that didn't work either ,eBay has some but they start at 1966 is...
hello ,putting together a 68 Roadrunner,bought a used 383 out of a70 roadrunner from eBay,cleaned up motor turns out its a 65 ,trying to find a damper bolt ,thought it was a 3/4 fine thread but that didn't work bought a 3/4 corse at local hardware store also NG ,there are some on eBay but they...