Search results for query: *

I have a built 392 whippled that I run a newer style tach. The tach runs off a msd signal wire to a dakota digital. Works great! Not sure how to go about using the stock tach. Sorry

Mopar505, you are a gentleman and a scholar! Thank you!

Link to the proper tools please :). Don't want to scrape up the bezel anymore than I have already if possible. Also, any idea on how many rotations to get it secure?

Replaced the ignition switch in my '69 plymouth (non column mounted) and it's really difficult to get the bezel to tighten and therefor the switch is a little sloppy. Is there a tool for this that grabs several of the slots at one time to turn it tightly? I've been using a small flathead to try...

Thanks for the replies all. Should have mentioned this is a modern Hemi swap efi with new gas tank/pump etc. I was thinking the vented gas cap should be changed to non-vented?

Hi all, Recently been parking my '69 plymouth in the attached garage and there is a very strong gas smell. IF I open the garage the smell permeates in about 10 minutes but it's very strong. Is there something I can do to lessen the odor and or eliminate it? My gas cap is vented and so it the...

Thank for the reply. I went to Ace Hardware and found similar bolts that work. The are a 1/4 20 by 1" square head bolt!

Long shot..... Any chance you'll make 2 more of these up and I'll buy them off you.... My housings were sloppy so I took apart my column and these 2 screws were not even there! Prior owner must have not put them back in and I can't seem to find them anywhere on the net!!

4/5/19 UPDATE I went to my local post office and had the PST shipping box with shredded paper weighed and then I placed my upper cam bolt in the box and had it weighed. As you will see the box with shredded paper weighs 11.50 Oz, which is very close to the RUDE representative's response that...

My one experience with PST has been horrible. I am upgrading the drum brakes to disc in my 1969 roadrunner (Gen 3 Hemi w/whipple). When I removed the upper control arm on the passenger side, one of the upper cam bolts broke. I went online and found that PST sells them for $15 each. I ordered...

Thanks!

Hello all, I have installed a Gen 3 6.4 in my '69RR with stock K member and a flaming river manual box. I installed the 2" TTI header on the driver side and then realized the tubes would not allow the starter to slide through or around them so I had to uninstall them and install the starter...

Holy smokes Mike thats alot of rings!!! Those appear to be just like the one that came out of the transmission housing. I picked up a pair of snap ring pliers (reverse) at O'reilly's and it appears they will open the ring wide enough to work. They are very much like the photo in Bobzilla's post...

Thanks Bob. I'll check my auto parts store first for those pliers, and then look online if I can't find the locally.

Mike, If its isn't too much too ask can you upload a pic of the part? If its the same I'd like to buy one from you if you're selling. Thank you.

Yes I am talking about that snap ring. I guess I should have checked an auto store instead of buying one online and at lowes. What is the correct name of the snap ring? When I called Oreillys they told me they didint have it but they had a front and rear trans seal. Also is there more than 1...

Ok guys I have not been able to install the Gear Vendor housing onto the 727 smallblock. Well technically I did once but then i realized that the transmission arm was not properly seated in the housing because it wouldn't shift so I unbolted the housing and attempted again. Unfortunately, I got...

493 Mike - You are the man! Many thanks!!

Hello again, I will attempt to install the gear vendors unit soon onto the 727. It has a reverse manual valve body and the GV instructions say to make sure the transmission is in 1st or L gear. I looked online and can't find an illustration of where the transmission arm would be on a 727...

Heck yeah guys...i did it. Praise God! I used the tool from Autozone called a blind hole puller. It's much better in my opinion than the pilot bushing puller from oreillys. Anyhow I rented both and swapped the 5lb slide hammer over to the blind hole puller because it came with a 3lb slide...