Search results for query: *

Howdy, Looking for some used 1967 gtx chrome valve covers. Repops are way out of my budget. Thanks

Howdy folks, Just had my first fuel pump pushrod wear out on me. It's oem from the 400 that is now a 451. Lost about .125" and it ruined my drive home. I don't have a carter that a lot of folks on here seem to have issues with, but I have an edelbrock 12-440-11 pump. Is it possible to snip a...

Howdy, Looking for the mounting bracket for a 1967 gtx flip gas cap. I'll attempt to fab one when i have time, but for now I'll keep an eye out for an original. I just missed one for sale on this site. Thanks.

My 1967 satellite has a '73 b body rad with 4 tabs. Will my fan still fit centered with that shroud? Or do i need to get a '67 rad for everything to line up? Thanks.

Has anybody ever seen these shock extensions? I got the s/s springs on there and was told to use these from the p.o. He says he's pretty sure they're direct connection parts. They have the DPCD stamp on them, but I feel like the plate would be a weak point unless I use a second plate to sandwich...

Howdy, Looking for a fender badge for a 1967 gtx. Not worried about pitting or the perfect piece. Anything to fill the two holes in the sheet metal. Thanks.

Howdy, For the life of me, I can't find dimensions online for the location of the trunk emblem holes for a '67 gtx. I seem to find fender locations, but none for the trunk. Can anyone here help me with some measurements? Thank you kindly.

Howdy, So with the intense heat and humidity here in the Montreal, I figured I'd inquire about why there is hot air constantly flowing out of my vents. It's a 1967 satellite that originally had a/c (which is long gone). My vent controls don't work and I thought my --warmer--> dial cable was...

Howdy, So I need a new driveshaft and I've read around about pushing the yoke in all the way and pulling out an inch. I can't bottom mine. I noticed some folks have a yoke seal that's about flush with the end of the tailshaft, but mine protrudes about an inch and starts to squish before I hit...

Howdy, My 1967 Satellite wiring is pretty bastardized, so nothing is even remotely where it should have been from the factory. I'm trying to properly route the headlight wires right now. I know some members have original cars, so some pictures from their cars would be mucho appreciated. I...

Howdy, My '67 Satellite driver's window moves front to rear a lot due to nothing holding it into the smokers window frame. Is this just aluminium/steel round bar? Or plastic? Or something special with rollers? Also, how would i go about getting it in there? Does that one piece come off, or...

Howdy, Just looking for windshield trim for my Satellite. I can't find repro anywhere, so if anyone could point me in the right direction, that would be awesome too. New or used, don't care. Just need something around my windshield. Thanks

Howdy, So this is more of a curiousity post than anything else. The past few times I drove my car, it would die when warming up. Start back up again no problems. But this time she died and wouldn't start. Lost spark. Tested the coil and the readings are all over the map, from .7 to 45 ohms...

Howdy, So i finally got my engine back in the car and put a few miles on her so far, but I've had to shift the car manually since on D it shifts waaay to quick. It's in 2nd by 8mph and 3rd between 12-14mph. I have a single rod kickdown that's been adjusted properly several times with the...

Howdy, I have a 727 from a 72 newport in my 67 satellite with a very leaky 3 prong neutral safety switch. It's bypassed i also just discovered, so i was wondering if i should wire up a 3 prong connector and get the same switch, or if i should find a proper single prong and see if it would fit...

Howdy folks, Just to clarify, me and wiring do not go well. Oil and water some might say. So I just finished installing my msd 6al-2 box and got it all set up except for the switched 12v source that everyone seems to have issues with. I've searched high and low and just can't figure out how...

Howdy all, Just found out my power steering pump brackets don't fit my new aluminium water pump housing. It's a federal pump, but was mounted to a drivers side lower rad hose housing. I went to a passenger side lower hose rad so i needed the change. It's a 440 source water pump housing. The...

Howdy, I need to upgrade my fuel lines from 5/16 to 3/8 to feed my new big block. Since I've read nothing but troubles with newer units, is it possible to modify my old unit that still reads levels correctly with a 3/8 pick up tube? Or just run a 3/8 line from the 5/16 outlet? Or is it less...

Howdy, I have decided to sell a bunch of parts for 383, 400 and 440 engines. They are all used and visually inspected for imperfections or cracks. I will provide pictures to interested parties. All prices are in CAD. Shipping not included, but can travel depending on item. I'm located just west...

Howdy, The 400 in my car has pitting in the cylinders, so I'm putting the top end together for my 383 magnum. I need new valve springs to go with what I'm told is an old crane 'cheater' cam. Something like .500 lift. It's going to be for street/strip use. There is such a wide variety of...