Search results for query: *

I own a Superbird that currently has an AMD rear window trim set on it. I found someone who is selling an original set. Does anyone know how to confirm that it is original? The seller is far away and I am only able to see pictures so far. Any help is appreciated!

Hi all! I am putting back together the first B Body project that I have done (it was a basket case). The car is a 1970 Roadrunner, and the horn button assembly and associated parts were missing when I bought the car. I have the steering wheel and a good used horn pad. I bought a reproduction...

Anyone have a picture of the correct location for the attaching point for the headlight ground wire on a Superbird? Thanks in advance!

Looking for the kickdown "Throttle Rod" that has the slot in it and goes from the carburetor throttle to the upper bell crank. 1970 440 4BBL car. I believe B body and E body are the same.

Wanted: Internal sure grip plate as is shown in the picture. I am having a 8 3/4" differential rebuilt and the gear shop found one of these plates has a broken tab. It is a early 1970 car with a 489 case. Need to buy one plate. He says that Summit has them listed but when he ordered it the part...

Looking for a ready to run 8 3/4" drop out 3rd member, 489 case, 3.55:1 Suregrip. If they are date coded, I would need something correct for a car with a build date of November 1969. Anyone have anything?

Hi all! I was wondering if anyone has any detailed photos on how the vacuum lines harness for the headlights are routed in the engine compartment? My car is a 70 Superbird 440 4BBL. Also, on the fuel line and brake line that runs front to rear, I bought a clip kit for each that came with the...

Hey fellow Mopar lovers! I am about ready to install my rebuilt 440 back into my Superbird. I have a lift and I plan to install it from underneath with the K frame and transmission (727 TF) as an assembly. I currently have both of the exhaust manifolds and the left stove pipe/heat shield...

Has anyone purchased a center dash trim from Classic Industries and has had good luck with it? It is this item https://www.classicindustries.com/product/mb179904.html I purchased one and the area where it meets the left dash trim above the steering column is about 1/4" to 5/16" out of...

Hi everyone! I have a 70 Roadrunner and I am trying to determine if the 7/8" plastic plugs that go into the upper half of the door frame on the hinge side should be white for a car with white upper door frames. If they are supposed to be white, can I buy white ones or do I have to paint them...

Hi everyone! I was wondering if I can get some opinions on the best way to install the lifters on a 440. I am to the point of my rebuild where I am installing the lifters, pushrods and rocker assemblies. This is a mostly stock engine with the only modifications being slightly larger valves, a...

Looking to buy an idle stop solenoid for a 1970 440 4BBL car. I believe the stamping on it is DR1114421.

Thank you for reading my post. I have a 1970 440 4BBL that is a 9.75:1 motor with a slightly larger than stock cam and slightly bigger valves, and running a stock 4BBL. I have seen posts about using a carb spacer to try to avoid the fuel from boiling out of the float bowl. I also have seen...

Hi everyone. Building a 440 that is relatively stock. It is .060" over (4.380" bore). Running about 10.3 to 1 compression with forged pistons. My sealed power rings (that are not file fit) have about .028" gap on the top ring and about .026" gap on the second ring. I see the desired spec for a...

Hi everyone! I just installed a new main wiring harness in my 1970 Roadrunner. The car was apart when I bought it so I am piecing this puzzle back together. The question I have is on the location of the two flasher units. There is one for the turn signals and one for the emergency flasher...

Hi All! I am looking for the following parts: Dual snorkel air cleaner for a 1970 440 4 BBL car Power Steering Cooler for a 1970 440 1970-71 Fury or 1970 Superbird front turn signal assemblies Rear Window Trim for a Superbird Thanks! Bob

My car has this added flange mounted to the underside of the cowl on the right side where the heater box mates up to the cowl. It is held on by 2 J bolts. Is this flange for a heater delete car? i am trying to install my non-AC heater box and it will not rotate up into position. It looks like if...

Wanted 1970 (same as 69?) B Body heater control assembly. Anyone know of one for sale? Thanks!

Wanted: Front turn signal housings and lenses for a Superbird (same housing as 1970-1971 Fury). Any one know of any for sale? Thank you!

I have a build sheet that was in my Superbird that belongs to another Superbird. The car is a B5 Blue 440 4BBL car. RM23U0A167xxx. If anyone knows of a car missing it's build sheet that matches this please have them contact me.