Search results for query: *

@RJRENTON @HEMI-ITIS @davek @6PKRTSE @68 HEMI GTS @66Satellite47 and I'm sure I'm missing some of the best who I hope will join in this thread... Here's the story, and I believe I need to change up my configuration: When I got my V-code 70 Roadrunner, it already had the (very nice) WIX 33033...

I was going to reinstall the fuel vapor separator, but the shop saw the line was plugged off and he cut the return line way back by the tank. The owner says when I install my 541 stroker the Carter M6903 120 GPH mechanical pump isn't going to provide the required fuel reliably. He says that the...

So I have a WIX metal fuel filter at the end of the hard line that comes from the gas tank, then the mechanical fuel pump, which is the :lowdown: Carter M6903, and then a metal reusable 40 micron low restriction inline filter that is part of the Promax lower fuel line, and then the 3 lines to...

I'm looking for any and all 3x2 intakes that are or can be modified to Max Wedge intake port size, single and dual plane designs. Also, does single plane necessarily mean poor street performance when the rest of the engine is a well balanced, complimentary selection of parts and performance? I...

I have the gauge that shows both O2 sensor readings in real time as A/F ratio or Lambda. Since I have the Edelbrock/Chrysler aluminum 6 bbl intake, which side of the intake feeds which side of the engine? Does the intake cross over or do the carburetors mainly feed the same side of the engine...

July 2018 Hot Rod Magazine https://www.hotrod.com/articles/holley-sniper-efi-install-dyno-test-440/

Many of you will know this. I left 3 clear site plugs in the fuel bowl sight holes longer than it took to check and adjust the float levels. I won't make excuses, I knew I shouldn't leave them in "too long"... Well any longer than it takes for the actual same day session to adjust the floats is...

I am starting a new thread even though Don Selleck is doing a great service to the forum by detailing his install. Here's an article about the FiTech 3x2 system installed on a 71 Challenger, originally a 440 6bbl (just like my 440). I haven't even read it yet, but as soon as I post this I'm...

I started this as a new thread to bring attention to a problem. A new problem. Changed out stock fuel pump to a Carter M6903. Changed upper and lower fuel lines to Promax braided stainless steel lines w/pressure gauge. Asked for a WIX 3/8ths fuel filter to match my V-code/Hemi factory 3/8ths...

70 Roadrunner, V-code, 3/8ths" fuel line. Current setup is hard fuel line from tank to 3/8ths rubber to fuel filter to 3/8ths rubber to hard line into fuel pump. Hard line out of pump to rubber line into vapor separator. Rubber return line from vapor separator back to tank. Rubber line to hard...

This is about non-Mopar in this instance, but a local car show attendee I know had All American Carburetors rebuild and RESTORE his 2 x 4bbl carbs for his big block Ford V-8 in his AC Shelby Cobra and he swears by them, their performance, and they do look great! I just sent my wife's 3 x 2bbl...

Way less expensive than others I've seen. Pre-orders available only. No additional tech support available yet regarding replacing our Mopar 3x2 Holley carbs. Pic: Link: https://fitechefi.com/products/39610/ Comments/information? :popcorn: UPDATE: I got some GREAT information from Norm at...

I spoke with a friend of mine at a car show yesterday who has a Cobra with a 428 and dual Holley 650s. He had both of them redone (like new) by All American Carburetors and tuned to his motor specs. He hasn't touched anything to make any adjustments since he got them back and swears by their...

I searched the forum and this section before posting. Is anyone using a six pack fuel injection/throttle body system? If so, please detail as much as possible. Thanks.