• When you click on links to various merchants on this site and make a purchase, this can result in this site earning a commission. Affiliate programs and affiliations include, but are not limited to, the eBay Partner Network.

The Roach

Richard Cranium said:
I have no idea. It's what came with the kit.
Click to expand...
They're commonly used with throttle body fuel injection kits. The El Camino had one with the Holley throttle body fuel injection kit. Holley recommends a separate fuel pressure regulator to dial in the correct pressure required by the injectors.
 
Richard Cranium said:
I have no idea. It's what came with the kit.
Click to expand...
That looks like the kit I got from Bouchillon when I built my Charger. I too tried that Corvette fuel filter / regulator. It was the only GM part on my 6.1 install. My engine must have know it and rejected it immediately. They are designed to regulate the fuel pressure at 58 psi but my engine didn't like what ever it was supplying. i ended up tossing the GM piece and installed an inline fuel filter in its place and bought an adjustable fuel regulator with a gauge and return. Much better setup IMO. Not sure why you needed to run the lines on the driver side though. Mine worked best on the passenger side. Here is a pic showing the regulator

100_9357.JPG
 
Sixpactogo said:
That looks like the kit I got from Bouchillon when I built my Charger. I too tried that Corvette fuel filter / regulator. It was the only GM part on my 6.1 install. My engine must have know it and rejected it immediately. They are designed to regulate the fuel pressure at 58 psi but my engine didn't like what ever it was supplying. i ended up tossing the GM piece and installed an inline fuel filter in its place and bought an adjustable fuel regulator with a gauge and return. Much better setup IMO. Not sure why you needed to run the lines on the driver side though. Mine worked best on the passenger side. Here is a pic showing the regulator

View attachment 1760722
Click to expand...


On my 392, the fuel line connector is on the driver's side (under the red cap)....

1732120255727.jpeg



My setup will look like this one below (seen at Carlisle last summer) and there's a lot going on the right side with the computer location, heater hoses, and the tight clearances against the firewall, so it was just as easy to route the fuel lines on the left side of the car.
1732120235231.jpeg
 
Richard Cranium said:
On my 392, the fuel line connector is on the driver's side (under the red cap)....

View attachment 1760738


My setup will look like this one below (seen at Carlisle last summer) and there's a lot going on the right side with the computer location, heater hoses, and the tight clearances against the firewall, so it was just as easy to route the fuel lines on the left side of the car.
View attachment 1760737
Click to expand...
Gotcha.....I hope that GM fuel filter/regulator works for you. Maybe mine was just a fluke but I am happier with the adjustable regulator and gauge.
 
HawkRod said:
Superb!

Looks like things are moving along at a very good pace. Any updates on when you think the car will be done? Will we see at Carlisle in 2025? :poke:
Click to expand...


I should get it running over the winter and final tweaking done in the spring (hopefully). Not sure if I'll take that or another survivor car to Carlisle.
 
2-ton lift to slide that baby in? …. I’m hitting Harbor Freight and finding a wrecked out modern challenger for an engine/trans :p


watermelon
 
eldubb440 said:
man, that's snug! I did the same thing yesterday, using the same technique!
Click to expand...


The only place that it's snug is against the firewall & the reworked wiper motor mounting area gave me the clearance that it needed. There's plenty of room left and right & the body dropped over the engine easily.

As a side note, a 440, with the factory hi-po exhaust manifolds on is just as wide as a hemi. Putting in Hemis & 440's require a lot more care because both engines require you to shift the body around the engine on the right side shock tower as you lower it down.

Before:
1732277715173.jpeg


After:
1732278329722.jpeg


Clearance to the shock towers, left & right:
1732278420344.jpeg


1732278440911.jpeg
 
You must log in or register to reply here.

Similar threads

Aron
'68 Charger Gen 3 Hemi Swap : Holley Program for 32 -1 / +1 Reluctor Wheel??
Replies
6
Views
778
Aron
Aron
Sixpactogo
Novelty Fender Tag
2
Replies
36
Views
4K
T Brashears
T Brashears
Vitamin_A12
‘70 ‘Pink Ribbon’ Road Runner Debut @ Moparty
2
Replies
21
Views
2K
Big D A12
Big D A12
HAHNAGON
Hemi swap planning recommendations? 69 Charger and 00 Dakota.
Replies
4
Views
1K
70chall440
70chall440
S
74 charger engine swap
Replies
8
Views
2K
ckessel
ckessel
Auto Transport Service
Back
Top