Search results for query: *

Just wondering if anyone has been to the Moparfest at the Battleship at Mobile, AL. Show is on April 26-27. It is a long way to travel for me, but I would go if it is a good show. Any opinions, suggestions or additional information including lodging is appreciated. PT in Tennessee 1968...

Finished a new shop with 12' ceiling, now ready to buy two post lift. How did you deal with the shipping? Can you get them delivered to a freight terminal and then pick it up there? Delivery to my residence could happen, but I would have to rent a fork lift to unload it. Will the freight...

I am taking my Roadrunner to this show next weekend. Just today saw some info that you could not put up a canopy unless you did it in the grass. There doesnt seem to be much grass. The picture shows most of the vehicles in an open parking lot. Weather is supposed to continue to be hot and humid...

I had asked this question about one year ago. I cannot get water flow thru my heater core. I am using a March Revolver system and it utilizes a PRW aluminum water pump. The water pump has two 3/4" NPT ports on the pump. One is close to the thermostst hole and one is furthur away. I cannot find...

pturner added a new event: Fun In The Sun Knoxville, Tennessee Read more about this event...

Is anyone going to the Mopars at the Rock (Rockingham, NC) April 16, 2022? Thinking about showing my 68 Roadrunner at this show. Any good info or ideas appreciated. thanks PT in Tennessee

I have installed a March pulley setup and they furnished a PRW aluminum water pump. There are two small NPT ports. This is on a 440 Big Block. Both ports are 3/4" NPT. One is closer to the thermostat housing and the other further away. I also have installed a Classic Air AC system. It has an...

Anyone here going to the Holley Moparty at Bowling Green, Sept. 10-12? I am going with my 68 Roadrunner Restomod. Registered online and received email confirmation, but no paperwork in the mail. Also showing at the small Music City Mopars show in Lebanon, Tennessee the following weekend. Anyone...

Anybody out there going to the Nats at Columbus in August? I am planning to go for three days (August 12-13-14) showing my 68 Roadrunner restomod. I have attended the show two times before, but never showing. I am registered for Judging, and parking for truck and trailer. I had stayed at the...

Need a enclosed car trailer, prefer 8 x 20 or larger to carry 1968 Roadrunner. i usually rent one from a Trailer rental company in Tennessee, but it was totaled last weekend in an accident. Have Toyota Tacoma to move it empty, but use a Dodge 3500 when it has a car inside. Willing to travel to...

My 1968 Roadrunner is a hardtop car (no post). The rear inside window top metal trim panels (where you attach the fuzzies) have a slight curve to them with a larger curve at the back. I have a fuzzy set with the rear larger upward curve, but the rest of the fuzzy is straight. Does anyone know if...

Is there some filler panel that goes behind the grill on my 68 Roadrunner? There are two tabs on the top hood support panel that turn down and two tabs on the bottom filler below the grille that turn up. The same on each side. My Roadrunner had been wrecked and never had a grill or the lower...

Don't know if anyone knows or cares, but Music City Mopars Club is having their annual free show this Saturday at Lebanon, Tennessee. Car judging, swap meet, and some famous folks and cars. Masks requested, but not required. I am going to be there with everything from my 68 Roadrunner that has...

Fabricated rotisserie in east Tennessee, Built from others plans. All professionally welded and machined. Three inch square tube lowers and towers. DOM tube for pivots. Tower is bolted at lower supports. Built to be fully adjustable, but specific plates and connections for my 1968 Roadrunner...

Trying to put door/window back together in my 68 Roadrunner RestoMod. I found i do not have this small screw/held on nose piece that is on the backside of the top of the vent window frame. the door window glass rolls up the back of the vent window frame up-into this nose piece. it is in usable...

Need to buy or swap for (1) Bench Seat lock Handle. This is the little cast cover that mounts to the cable locking arm mounted in the outside of the folding bench seat. it has a slot on the back side and is held with a small socket head cap screw (Allen Head). For 68 Roadrunner, but don't know...

Does anyone know how the 68 era B Bodies got wiring to the door for the power windows? Seems I have seen just two wires clamped to the hinge. I guess there were only power wire and ground to the switches. Were the wires in a loom or rubber accordion boot? Did it go where the small "dimple" is...

I have a Bench Seat Tilt Latch cable that is mangled. it could be reworked with new flex cable, but does anyone know of a repop or someone that might have a NOS. it is a Left (drivers side) cable for a 68 Roadrunner. I would also buy a good used one. thanks for any info or help. PT in Tennessee

Anyone going to the Music City Mopars show in Lebanon Tennessee Sept. 26-28? this is a smaller show but really has some nice cars. it is a free show unless you want to show your car. at the Wilson county fair grounds. Several beautiful cars from Kingsport always there. is there other shows in...

My 68 Roadrunner doors have small dimples from inside to the outside where the door handles were mounted. they look like they could be from the 1/4 x 20 bolts being tightened to tight and the metal being pulled outward. both doors look really similar, but not exactly the same. they could also be...